Previously, on DHCPv4 address renewal, the old address may be removed
while the new address is not ready yet.
This also simplifies the logic of removing address and routes.
In NetworkdBridgeTests.test_bridge_configure_without_carrier of
systemd-networkd-tests.py
```
bridge99: MAC address: 2e:3a:ec:4d:d3:62
Assertion 'sd_ipv4ll_is_running(ll) == 0' failed at src/libsystemd-network/sd-ipv4ll.c:110, function int sd_ipv4ll_set_mac(sd_ipv4ll *, const struct ether_addr *)(). Ignoring.
bridge99: Could not update MAC address in IPv4LL client: Device or resource busy
```
When DHCP6 and RA are enabled, and RA does not provide any addresses,
then link may become configured state even if no address is assigned,
due to the time-lag between RA completion and DHCP reply.
This makes if DHCP is explicitly enabled, then link must have at least
one valid address to be in the configured state.
While investigating https://github.com/systemd/systemd/issues/16356, I
discovered that networkd stops the radv service before adding or updating
prefixes and then starts it again. This causes networkd to send an RA with
a router lifetime of zero, causing the routes to flap on systems receiving
the RA for a fraction of a second before radv is started again and proper
RAs are sent. That has the potential to cause issues with latency-sensitive
traffic like gaming or VoIP. This patch adds a boolean argument to the
sd_radv_stop() function to control this behavior. The zero lifetime RA is
still sent whenever radv is actually being stopped, but when it is being
restarted for a prefix update (from networkd-dhcp6.c), the final RA is no
longer sent to avoid the route flapping.
SR-IOV provides the ability to partition a single physical PCI
resource into virtual PCI functions which can then be injected in
to a VM. In the case of network VFs, SR-IOV improves north-south n
etwork performance (that is, traffic with endpoints outside the
host machine) by allowing traffic to bypass the host machine’s network stack.
I'm not sure if I understand the code correctly, but it seems that if
storig in the second set failed, we'd return with the first set having
no reference on the link object, and the link object could be freed in the
future, leaving the set with a dangling reference.
Patch contains a coccinelle script, but it only works in some cases. Many
parts were converted by hand.
Note: I did not fix errors in return value handing. This will be done separate
to keep the patch comprehensible. No functional change is intended in this
patch.
This is an attempt to clean up the POP3/SMTP/LPR/… DHCP lease server
data logic in networkd. This reduces code duplication and fixes a number
of bugs.
This removes any support for collecting POP3/SMPT/LPR servers acquired
via local DHCP client releases since noone uses that, and given how old
these protocols are I doubt this will change. It keeps support for
configuring them for the dhcp server however.
The differences between the DNS/NTP/SIP/POP3/SMTP/LPR configuration
logics are minimized.
This removes the relevant symbols from sd-network.h (which is an
internal API only at this point after all).
This is unfortunately not well test, given the old code for this had
barely any tests. But the new code should not perform worse at least,
and allow us to release, since it corrects some interfaces visible in
the .network configuration format.
Fixes: #15943
To make Driver= in [Match] section work in containers.
Note that ID_NET_DRIVER= property in udev database is set with the
result of the ethtool. So, this should not change anything for
non-container cases.
Closes#15678.
This is an attempt to clean-up the DHCP lease server type code a bit. We
now strictly use the same enum everywhere, and store server info in an
array. Moreover, we use the same nomenclature everywhere.
This only makes the changes in the sd-dhcp code. The networkd code is
untouched so far (but should be fixed up like this too. But it's more
complicated since this would then touch actual settings in .network
files).
Note that this also changes some field names in serialized lease files.
But given that these field names have not been part of a released
version of systemd yet, such a change should be ok.
This is pure renaming/refactoring, shouldn't actually change any
behaviour.
In DHCPv6-PD environment, where WAN interface requests IPv6 via DHCPv6,
receives the address as well as delegated prefixes, with LAN interfaces
serving those delegated prefixes in their router advertisement messages.
The LAN interfaces on the router themselves do not have
the IPv6 addresses assigned by networkd from the prefix it
serves on that interface. Now this patch enables it.
We'd start writing an entry line, then another one, then another one,
and then output the rest of the first one, and then some other random
stuff, and the rest of some other lines... Results were ...eh... random.
Let's define a helper to avoid some of the copy&paste madness, and separate
blocks that output a single line with /**********************************/.
This rework doesn't change what data is written, it only tries to fix the
format of the output. The fact that some entries only write data from
link->network, and some from either link->network or link, some stuff only
for dhpc4 leases while some for both dhpc4 and dhcp6, etc, looks rather
suspicious too, but I didn't touch this.
Defines how link-local and autoconf addresses are generated.
0: generate address based on EUI64 (default)
1: do no generate a link-local address, use EUI64 for addresses generated
from autoconf
2: generate stable privacy addresses, using the secret from
stable_secret (RFC7217)
3: generate stable privacy addresses, using a random secret if unset
Link groups are similar to port ranges found in managed switches.
You can add network interfaces to a numbered group and perform operations
on all the interfaces from that group at once.
Commit 08c588d18b moved attachment of the
sd-event into creation of the dhcp_client or ipv4ll in dhcp4_configure()
or ipv4ll_configure(), but these can also be created in link_load(),
so that creation needs to also perform sd-event attachment.
Without this, dhcp_client or ipv4ll created in link_load() will not have
an ->event and will fail assertion, causing networkd to fail, e.g.:
Assertion 'client->event' failed at src/libsystemd-network/sd-dhcp-client.c:1283, function client_start_delayed(). Ignoring.
ens2: Could not acquire DHCPv4 lease: Invalid argument
ens2: Failed
Interfaces may come up at any time, even during our initialization of
them, for various reasons; e.g. the kernel will raise VLAN when its
parent is raised; or we will raise an interface if configured with
BindCarrier and its associated interfaces come up.
When LinkLocalAddressing has been disabled for ipv6, we disable
addr_gen_mode in the kernel, so it will not automatically create a
ipv6ll address when the interface is raised. However, we currently
drop all foreign addresses before disabling addr_gen_mode.
If the link has been up for a long time, then its kernel-created ipv6ll
address will be correctly dropped. If the link is down, and stays
down until we raise it after finishing configuration, the addr_gen_mode
setting will be disabled when the interface is raised and the kernel
will not create any ipv6ll address.
However, if the interface is raised after dropping foreign config,
but before we have disabled addr_gen_mode, the kernel will create a
ipv6ll tentative address that will eventually finish DAD and become a
working ipv6ll address, even though we have been configured to disable
ipv6ll.
Moving our call to drop foreign addresses to after we have successfully
set addr_gen_mode closes this window; after we disable addr_gen_mode,
we can safely remove foreign ipv6ll addresses (including tentative ones)
and be sure that the kernel will not create any more.
Fixes: #13882.
The kernel will create an ipv6ll tentative address immediately when an
interface is raised if addr_gen_mode is not disabled; and, the kernel does
not notify netlink listeners about any tentative addresses. So it's
possible for an interface to contain tentative ipv6 link-local address(es)
that networkd doesn't know about when all foreign addresses are dropped.
In this case, networkd is later notified about the new ipv6ll address(es)
after they finish DAD and are no longer tentative; but since that's after
networkd has already dropped foreign addresses, they are incorrectly left
on the interface.
Similar to the link->setting_mtu flag, this delays continued configuration
until after the genmode has been successfully set; this is important
because we do not want networkd to raise the interface before the genmode
has been set, as if we're disabling the genmode, raising the interface
before we have successfully disabled the genmode will result in the kernel
creating a ipv6ll address, even though we don't want that.
If the interface is in initialized state, no network file is assigned to
the interface. If an interface is not managed by networkd, previously,
the foreign configs of the interface was dropped.
Fixes#14250.
The kernel resets the ipv6 mtu after NETDEV_UP or NETDEV_CHANGEMTU event,
so we must reset the ipv6 mtu to our configured value after we detect
IFF_UP flag set or after we set the device mtu.
Fixes: #13914.
This switches detect_container() to path_is_read_only_rw("/sys"), as if
systemd-udevd.service is conditionalized with that way.
This also updates the log message.
This partially reverts 95355a281c.
It seems that other parts of link_stop_clients() should be skipped
when restarting, but I don't know enough about those other clients to have
an opinion if it is better to stop&start them on restart or not.
Anyway, that can be done in later patches now that the support for restarts
is there.
Fixes#13625.
When nspawn container with private network starts, networkd creates
the default route for the interface. The route may cause problem on
the host side, and it can be created with DefaultRouteOnDevice= now.
Hence, this makes networkd not create the route implicitly any more.
Closes#13418.
*We* control the sysctl setting. If the user configured IPv6, then we apply the
settings, and just make sure that at some point during the configuration the
sysctl is disabled (i.e. ipv6 enabled) if we have IPv6 configured.
Replaces #13283.
Otherwise, changing the default gateway doesn't purge old gateway routes
left on the system during daemon restart. This also fixes removing other
foreign gateway routes that don't match the expected configuration.
Tested:
Changed gateway addresses prior to the patch and they lingered on
the system during each reconfiguration. Applied this patch and
reconfigured gateways and other routes multiple times and it removed
the foreign routes that had gateways that didn't match.
Signed-off-by: William A. Kennington III <william@wkennington.com>
The flag IFA_F_NOPREFIXROUTE was introduced in kernel-3.14. But even if
the kernel does not support the flag, it should be just ignored. So, it
is not necessary to do the fallback logic. Moreover, the current logic
is not a fallback mechanism but just retrying. So, it should not work.
Let's drop that.
Some path of configuring address, route or etc., go to failed state, but
some do not. E.g., failure in address configuration which is provided by
DHCPv4 goes to failed state, but static address does not.
This is just for consistency. This should not change anything if
everything is fine.
This also voidify manager_rtnl_process_address().
When DHCP or any other dynamic addresses are changed, then
link_request_set_routes() is invoked, and even if no static routes
are configured, the operational state is needlessly changed to
configuring state.
This makes the state is changed only when static routes are configured.
Fixes#12931.
In file included from ../src/basic/macro.h:558,
from ../src/basic/alloc-util.h:9,
from ../src/network/networkd-link.c:7:
../src/network/networkd-link.c: In function ‘link_sysctl_ipv6_enabled’:
../src/basic/log.h:107:9: error: ‘%s’ directive argument is null [-Werror=format-overflow=]
107 | log_internal_realm(LOG_REALM_PLUS_LEVEL(LOG_REALM, (level)), __VA_ARGS__)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../src/shared/log-link.h:21:25: note: in expansion of macro ‘log_internal’
21 | log_internal(level, error, _FILE_, __LINE__, __func__, ##__VA_ARGS__); \
| ^~~~~~~~~~~~
../src/shared/log-link.h:33:50: note: in expansion of macro ‘log_link_full’
33 | #define log_link_warning_errno(link, error, ...) log_link_full(link, LOG_WARNING, error, ##__VA_ARGS__)
| ^~~~~~~~~~~~~
../src/network/networkd-link.c:83:24: note: in expansion of macro ‘log_link_warning_errno’
83 | return log_link_warning_errno(link, r,
| ^~~~~~~~~~~~~~~~~~~~~~
../src/network/networkd-link.c:84:77: note: format string is defined here
84 | "Failed to read net.ipv6.conf.%s.disable_ipv6 sysctl property: %m",
| ^~
cc1: some warnings being treated as errors
Previously, when a bridge or bonding interface is in degraded-carrier
state, then we cannot judge the interface has addresses or not.
By using the new states, dbus clients can distinguish such situation.
Otherwise, the interface cannot be in "configured" state, as ipv6 link local
addressing is enabled by default. Note that even if ConfigureWithoutCarrier=
is set, all dynamic configurations are checked when the interface has
carrier.
