systemd.show-status=error is useful for the case where people care about errors
only.
If people want to have a quiet boot, they most likely don't want to see all
status output even if there is a delay in boot, so make "quiet" imply
systemd.show-status=error instead of systemd.show-status=auto.
Fixes#14976.
We would flip to status=temporary mode on the first error, and then switch back
to status=auto after the initial transaction was done. This isn't very useful,
because usually all the messages about successfully started units and not
related to the original failure. In fact, all those messages most likely cause
the information about the prime error to scroll off screen. And if the user
requested quiet boot, there's no reason to think that they care about those
success messages.
Also, when logging about dependency cycles, treat this similarly to a unit
error and show the message even if the status is "soft disabled" (before we
wouldn't show it in that case).
When we are booting with show-status=on, normally new status updates happen a
few times per second. Thus, it is reasonable to start showing the cylon eye
after 5 s, because that means a significant delay has happened. When we are
running with show-status=off or show-status=auto (and no error had occured),
the user is expecting maybe 15 to 90 seconds with no output (because that's
usually how long the whole boot takes). So we shouldn't bother the user with
information about a few seconds of delay. Let's make the timeout 25s if we are
not showing any messages.
Conversly, when we are outputting status messages, we can show the cylon eye
with a shorter delay, now that we removed the connection to enablement status.
Let's make this 2s, so users get feedback about delays more quickly.
We know if we created the file before, no need to repeat the operation. The
state in /run should always match our internal state. Since we call
manager_set_show_status() quite often internally, this saves quite a few
pointless syscalls.
We would say "Enabling" also for SHOW_STATUS_AUTO, which is actually
"soft off". So just print the exact state to make things easier to understand.
Also add a helper function to avoid repeating the enum value list.
For #14814.
Where we have a device that looks like a mouse and is connected over i2c, tag
it as pointing stick. There is no such thing as a i2c mouse.
Even touchpads that aren't recognized by the kernel will not show up as i2c
mouse - either the touchpad follows the Win8.1 specs in which case the kernel
switches it to multitouch mode and it shows up like a touchpad. The built-in
trackpoint, if any, is then the i2c mouse device.
Where the touchpad doesn't follow the spec, the kernel will not handle it and
the touchpad remains on the PS/2 legacy bus - not i2c. Hence we can assume
that any i2c mouse device is really a pointing stick.
This prevents an error in pam_systemd when logging in.
sshd[2623165]: pam_unix(sshd:session): session opened for user tony.stark(uid=10001) by (uid=0)
sshd[2623165]: pam_systemd(sshd:session): Failed to get user record: Invalid argument
Bug: https://bugs.gentoo.org/708824
Currently, if deactivation of the primary swap unit fails:
# LANG=C systemctl --no-pager stop dev-mapper-fedora\\x2dswap.swap
Job for dev-mapper-fedora\x2dswap.swap failed.
See "systemctl status "dev-mapper-fedora\\x2dswap.swap"" and "journalctl -xe" for details.
then there are still the running stop jobs for all the secondary swap units
that follow the primary one:
# systemctl list-jobs
JOB UNIT TYPE STATE
3233 dev-disk-by\x2duuid-2dc8b9b1\x2da0a5\x2d44d8\x2d89c4\x2d6cdd26cd5ce0.swap stop running
3232 dev-dm\x2d1.swap stop running
3231 dev-disk-by\x2did-dm\x2duuid\x2dLVM\x2dyuXWpCCIurGzz2nkGCVnUFSi7GH6E3ZcQjkKLnF0Fil0RJmhoLN8fcOnDybWCMTj.swap stop running
3230 dev-disk-by\x2did-dm\x2dname\x2dfedora\x2dswap.swap stop running
3234 dev-fedora-swap.swap stop running
5 jobs listed.
This remains endlessly because their JobTimeoutUSec is infinity:
# LANG=C systemctl show -p JobTimeoutUSec dev-fedora-swap.swap
JobTimeoutUSec=infinity
If this issue happens during system shutdown, the system shutdown appears to
get hang and the system will be forcibly shutdown or rebooted 30 minutes later
by the following configuration:
# grep -E "^JobTimeout" /usr/lib/systemd/system/reboot.target
JobTimeoutSec=30min
JobTimeoutAction=reboot-force
The scenario in the real world seems that there is some service unit with
KillMode=none, processes whose memory is being swapped out are not killed
during stop operation in the service unit and then swapoff command fails.
On the other hand, it works well in successful case of swapoff command because
the secondary jobs monitor /proc/swaps file and can detect deletion of the
corresponding swap file.
This commit fixes the issue by finishing the secondary swap units' jobs if
deactivation of the primary swap unit fails.
Fixes: #11577
If the peripheral device type is that of a host managed zone block device (0x14),
the device supports the same identification mechanisms as conventional disks (0x00).
The problem with the original form is that the subject of the sentence with
passive void is "the system", and we're not inhibiting the system. In English
the sense can be made out, but the form is gramatically incorrect.
In fact, the Polish translation got this wrong:
> msgid "Power off the system while an application is inhibiting this"
> msgstr "Wyłączenie systemu, kiedy program zażądał jego wstrzymania"
"jego" can only refer to "the system", because of gender mismatch with "power
off". If our translators cannot grok the message, then we should probably reword
it.
Also, drop the "asked to" part. Everything we do is over IPC, so we only ever
"ask" for things, and this adds no value.
"home" is okay-ish in English, but rather awkward in many other languages.
For example, even before this change, in fr.po we had "un espace personnel"
as the translation everywhere. Let's use a less overloaded term.
Fixes#14789.
The enum used for column names is integer type while table_set_display() is parsing
arguments on size_t alignment which may result in assert in table_set_display() if
the size between types missmatch. This patch cast the enums to size_t.
It also fixes all other occurences for table_set_display() and
table_set_sort().
The enum used for column names is integer type while table_set_display() is parsing
arguments on size_t alignment which may result in assert in table_set_display() if
the size between types missmatch. This patch cast the enums to size_t.
An alternative solution would be to change the table_set_display() function
arguments to unsigned type.
In order to allow other parts of systemd-networkd to use sets/hashmaps
of Address objects, the address_hash_ops structure needs to be made
available to them.
The RFC 7217 (prefixstable) algorithm can use Duplicate Address
Detection to produce multiple candidate addresses, but the implementation
here does not currently employ that mechanism.
This error message will be emitted when any form of SLAAC address
generation fails, not just 'prefix stable', so the message should
only refer to SLAAC.
The logic which can produce an IPv6 address using SLAAC produces an
address, not a prefix, so the boolean variable used to detect whether
it succeeded should reflect that.
Add shortcuts to enable and start, or disable and stop, portable
services with a single portablectl command.
Allow to pass a filter on detach, as it's necessary to call
GetImageMetadata to get the unit names associated with an image.
Fixes#10232
