Files which are installed as-is (any .service and other unit files, .conf
files, .policy files, etc), are left as is. My assumption is that SPDX
identifiers are not yet that well known, so it's better to retain the
extended header to avoid any doubt.
I also kept any copyright lines. We can probably remove them, but it'd nice to
obtain explicit acks from all involved authors before doing that.
When trying to read keyfiles from an encrypted partition to unlock the swap,
a cyclic dependency is generated because systemd can not mount the
filesystem before it has checked if there is a swap to resume from.
Closes#3940
Add a synchronization point so that custom initramfs units can run
after the root device becomes available, before it is fsck'd and
mounted.
This is useful for custom initramfs units that may modify the
root disk partition table, where the root device is not known in
advance (it's dynamically selected by the generators).
This did not really work out as we had hoped. Trying to do this upstream
introduced several problems that probably makes it better suited as a
downstream patch after all. At any rate, it is not releaseable in the
current state, so we at least need to revert this before the release.
* by adjusting the path to binaries, but not do the same thing to the
search path we end up with inconsistent man-pages. Adjusting the search
path too would be quite messy, and it is not at all obvious that this is
worth the effort, but at any rate it would have to be done before we
could ship this.
* this means that distributed man-pages does not make sense as they depend
on config options, and for better or worse we are still distributing
man pages, so that is something that definitely needs sorting out before
we could ship with this patch.
* we have long held that split-usr is only minimally supported in order
to boot, and something we hope will eventually go away. So before we start
adding even more magic/effort in order to make this work nicely, we should
probably question if it makes sense at all.
In particular, use /lib/systemd instead of /usr/lib/systemd in distributions
like Debian which still have not adopted a /usr merge setup.
Use XML entities from man/custom-entities.ent to replace configured paths while
doing XSLT processing of the original XML files. There was precedent of some
files (such as systemd.generator.xml) which were already using this approach.
This addresses most of the (manual) fixes from this patch:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/patches/Fix-paths-in-man-pages.patch?h=experimental-220
The idea of using generic XML entities was presented here:
http://lists.freedesktop.org/archives/systemd-devel/2015-May/032240.html
This patch solves almost all the issues, with the exception of:
- Path to /bin/mount and /bin/umount.
- Generic statements about preference of /lib over /etc.
These will be handled separately by follow up patches.
Tested:
- With default configure settings, ran "make install" to two separate
directories and compared the output to confirm they matched exactly.
- Used a set of configure flags including $CONFFLAGS from Debian:
http://anonscm.debian.org/cgit/pkg-systemd/systemd.git/tree/debian/rules
Installed the tree and confirmed the paths use /lib/systemd instead of
/usr/lib/systemd and that no other unexpected differences exist.
- Confirmed that `make distcheck` still passes.
It is annoying when we have dead links on fd.o.
Add project='man-pages|die-net|archlinux' to <citerefentry>-ies.
In generated html, add external links to
http://man7.org/linux/man-pages/man, http://linux.die.net/man/,
https://www.archlinux.org/.
By default, pages in sections 2 and 4 go to man7, since Michael
Kerrisk is the autorative source on kernel related stuff.
The rest of links goes to linux.die.net, because they have the
manpages.
Except for the pacman stuff, since it seems to be only available from
archlinux.org.
Poor gummiboot gets no link, because gummitboot(8) ain't to be found
on the net. According to common wisdom, that would mean that it does
not exist. But I have seen Kay using it, so I know it does, and
deserves to be found. Can somebody be nice and put it up somewhere?
First, rename root-fs.target to initrd-root-fs.target to clarify its usage.
Mount units with "x-initrd-rootfs.mount" are now ordered before
initrd-root-fs.target. As we sometimes construct /sysroot mounts in
/etc/fstab in the initrd, we want these to be mounted before the
initrd-root-fs.target is active.
initrd.target can be the default target in the initrd.
(normal startup)
:
:
v
basic.target
|
______________________/|
/ |
| sysroot.mount
| |
| v
| initrd-root-fs.target
| |
| v
| initrd-parse-etc.service
(custom initrd services) |
| v
| (sysroot-usr.mount and
| various mounts marked
| with fstab option
| x-initrd.mount)
| |
| v
| initrd-fs.target
| |
\______________________ |
\|
v
initrd.target
|
v
initrd-cleanup.service
isolates to
initrd-switch-root.target
|
v
______________________/|
/ |
| initrd-udevadm-cleanup-db.service
| |
(custom initrd services) |
| |
\______________________ |
\|
v
initrd-switch-root.target
|
v
initrd-switch-root.service
|
v
switch-root
This replaces the symlink based dependency by an explicit one in the
unit file so that we avoid the dangling symlink when no display manager
is installed.
Zbigniew Jędrzejewski-Szmek