"systemctl load" has always been racy since the GC could hit any time,
before making use of the loaded unit. Very recent systemd will run GC
immeidately after all unit state changes which has the effect that the
the effect of "systemctl load" is completely gone now, so let's remove
the support for it in "systemctl" for good.
"systemctl set-log-level" is a command for analysis and tracing hence
"systemd-analyze" should be the better home for it, thus allowing us to
make the overly large "systemctl" a bit smaller.
It's an analysis command and its format is explicitly not covered by any
stability guarantees, hence move away from systemctl and into
systemd-analyze, minimizing the already large interface of systemctl a
bit.
This patch also adds auto-paging to the various systemd-analyze commands
where that makes sense
Use proper grammar, word usage, adjective hyphenation, commas,
capitalization, spelling, etc.
To improve readability, some run-on sentences or sentence fragments were
revised.
[zj: remove the space from 'file name', 'host name', and 'time zone'.]
This mirrors --property, and is generally useful.
New functionality is used in bash completion.
In case of zsh completion, new functionality is less useful
because of caching. Nevertheless, zsh completion for restart
is made to behave more-or-less the same as bash completion.
At least sockets can be restarted.
Occasionally people report problem with reboot/poweroff operations hanging in
the middle. One known cause is when a new transaction to start a unit is
enqueued while the shutdown is going on. The start of the unit conflicts with
the shutdown jobs, so they get cancelled. The failure case can be quite unpleasant,
becase getty and sshd may already be stopped.
Fix it by using irreversible jobs for shutdown (reboot/poweroff/...) actions.
This applies to commands like "reboot", "telinit 6", "systemctl reboot". Should
someone desire to use reversible jobs, they can say "systemctl start reboot.target".`
Add a new job mode: replace-irreversibly. Jobs enqueued using this mode
cannot be implicitly canceled by later enqueued conflicting jobs.
They can however still be canceled with an explicit "systemctl cancel"
call.
"systemctl default" should behave identically to "telinit N" (where N is the
corresponding runlevel target number), therefore it should use isolate job mode
too.
This makes 'status' behave like 'list-units':
systemctl status -> status of all units
systemctl -t error status -> status of error units
systemctl -t mount status -> etc.
Option listings seemed to be pretty much random, some were short opt,
long opt, others were long opt, short opt. This just makes every option
with a short and long opt that I could find in the order short opt, long
opt, for formatting's sake.
New sections are added: PAM options, crypttab options, commandline
options, miscellaneous. The last category will be used for all
untagged <varname> elements.
Commandline options sections is meant to be a developer tool: when
adding an option it is sometimes useful to be able to check if
similarly named options exist elsewhere.
systemctl list-dependencies lists all unit's dependecies and
recursively expands all subsidiary target units into a tree.
Primary purpose for this command is to show all units which are
enabled in specified target.
New file output.h with output flags and modes.
--full parameter also for cgls and loginctl.
Include 'all' parameter in flags (show_cgroup_by_path, show_cgroup,
show_cgroup_and_extra, show_cgroup_and_extra_by_spec).
get_process_cmdline with max_length == 0 will not ellipsize output.
Replace LINE_MAX with 0 in some calls of get_process_cmdline.
[zj: Default to --full when under pager for clgs.
Drop '-f' since it wasn't documented and didn't actually work.
Reindent a bit.
]
Adds is-failed to join is-active and is-enabled.
I grabbed this one from the todo list. Most of the functionality was
already there for is-active. I just needed to make check_one_unit take
the states to check for as an argument instead of the hardcoded
"active" and "reloading".
is-failed will return 1 if none of the units given are failed. This is
different from is-active which will return 3 if none of the units
given are active. It returns 3 with this comment:
/* According to LSB: "program is not running" */
As that does not make sense when looking for failed units I simply
chose 1 instead.
https://bugs.freedesktop.org/show_bug.cgi?id=55890
Fixed typos, serial comma, and removed "either" as there were more
than two options. Also did an extra rename of "system-shutdown"
to "systemd-shutdown" that was forgotten in commit
8bd3b8620c
Given that "journalctl -u" exists now there's no need to duplicate this
functionality in systemctl, so let's drop this, especially given that it
always felt a bit awkward to overload "-f" to both --force and --follow,
and to have continues output with a status header for this.
systemctl status -f avahi-daemon
now becomes:
journalctl -fu avahi-daemon
Which is shorter and a lot less redundant.
E.g. systemctl --all -t masked gives the list of masked units.
The -t/--type option is reused. This is possible because unit types
and unit load states are called differently, so it is possible to
distinguish what the user meant. Using the same option also means that
the interface is user for the user: less options to remember.
