The kernel resets the ipv6 mtu after NETDEV_UP or NETDEV_CHANGEMTU event,
so we must reset the ipv6 mtu to our configured value after we detect
IFF_UP flag set or after we set the device mtu.
Fixes: #13914.
This option is an indication for PID1 that the entry in crypttab is handled by
initrd only and therefore it shouldn't interfer during the usual start-up and
shutdown process.
It should be primarily used with the encrypted device containing the root FS as
we want to keep it (and thus its encrypted device) until the very end of the
shutdown process, i.e. when initrd takes over.
This option is the counterpart of "x-initrd.mount" used in fstab.
Note that the slice containing the cryptsetup services also needs to drop the
usual shutdown dependencies as it's required by the cryptsetup services.
Fixes: #14224
Like with shmat already the actual results of the test
test_memory_deny_write_execute_mmap depend on kernel/libseccomp/glibc
of the platform it is running on.
There are known-good platforms, but on the others do not assert success
(which implies test has actually failed as no seccomp blocking was achieved),
but instead make the check dependent to the success of the mmap call
on that platforms.
Finally the assert of the munmap on that valid pointer should return ==0,
so that is what the check should be for in case of p != MAP_FAILED.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
At the beginning of seccomp_memory_deny_write_execute architectures
can set individual filter_syscall, block_syscall, shmat_syscall values.
The former two are then used in the call to add_seccomp_syscall_filter
but shmat_syscall is not.
Right now all shmat_syscall values are the same, so the change is a
no-op, but if ever an architecture is added/modified this would be a
subtle source for a mistake so fix it by using shmat_syscall later.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
If seccomp_memory_deny_write_execute was fatally failing to load rules it
already returned a bad retval.
But if any adding filters failed it skipped the subsequent seccomp_load and
always returned an rc of 0 even if no rule was loaded at all.
Lets fix this requiring to (non fatally-failing) load at least one rule set.
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
This switches detect_container() to path_is_read_only_rw("/sys"), as if
systemd-udevd.service is conditionalized with that way.
This also updates the log message.
If /sys is read only filesystem, e.g., nspawn is running in container,
then usually udev is not running. In such a case, let's assume that
the interface is already initialized. Also, this makes nspawn refuse
to use the network interface which is under renaming.
Fixes#14223.
Properties marked this way really shouldn't be sent around willy-nilly,
that's what the flag is about, hence exclude it from InterfacesAdded
signals (and in fact anything that is a signal).
This allows marking messages that contain "sensitive" data with a flag.
If it's set then the messages are erased from memory when the message is
freed.
Similar, a flag may be set on vtable entries: incoming/outgoing message
matching the entry will then automatically be flagged this way.
This is supposed to be an easy method to mark messages containing
potentially sensitive data (such as passwords) for proper destruction.
(Note that this of course is only is as safe as the broker in between is
doing something similar. But let's at least not be the ones at fault
here.)
Stochastic Fairness Queueing is a classless queueing discipline.
SFQ does not shape traffic but only schedules the transmission of packets, based on 'flows'.
The goal is to ensure fairness so that each flow is able to send data in turn,
thus preventing any single flow from drowning out the rest.
So far we silently convert negative return values from run() as
EXIT_FAILURE, which is how UNIX expects it. In many cases it would be
very useful for the caller to retrieve the actual error number we exit
with. Let's generically return that via sd_notify()'s ERRNO= attribute.
This means callers can set $NOTIFY_SOCKET and get the actual error
number delivered at their doorstep just like that.
This adds a new safe_fork() flag. If set the child process' fd 1 becomes
fd 2 of the caller. This is useful for invoking tools (such as various
mkfs/fsck implementations) that output status messages to stdout, but
which we invoke and don't want to pollute stdout with their output.
The actual burst limit is modified by the remaining disk space. This
isn't mentioned anywhere in the available documentation and might be a
source of surprise for an end user expecting certain behaviors.
