asin and acos have slow paths for rounding the last bit that cause some
calls to be 500-1500x slower than average calls.
These slow paths are rare, a test of a trillion (1.000.000.000.000)
random inputs between -1 and 1 showed 32870 slow calls for acos and 4473
for asin, with most occurrences between -1.0 .. -0.9 and 0.9 .. 1.0.
The slow paths claim correct rounding and use __sin32() and __cos32()
(which compare two result candidates and return the closest one) as the
final step, with the second result candidate (res1) having a small offset
applied from res. This suggests that res and res1 are intended to be 1
ULP apart (which makes sense for rounding), barring bugs, allowing us to
pick either one and still remain within 1 ULP of the exact result.
Remove the slow paths as the accuracy is better than 1 ULP even without
them, which is enough for glibc.
Also remove code comments claiming correctly rounded results.
After slow path removal, checking the accuracy of 14.400.000.000 random
asin() and acos() inputs showed only three incorrectly rounded
(error > 0.5 ULP) results:
- asin(-0x1.ee2b43286db75p-1) (0.500002 ULP, same as before)
- asin(-0x1.f692ba202abcp-4) (0.500003 ULP, same as before)
- asin(-0x1.9915e876fc062p-1) (0.50000000001 ULP, previously exact)
The first two had the same error even before this commit, and they did
not use the slow path at all.
Checking 4934 known randomly found previously-slow-path asin inputs
shows 25 calls with incorrectly rounded results, with a maximum error of
0.500000002 ULP (for 0x1.fcd5742999ab8p-1). The previous slow-path code
rounded all these inputs correctly (error < 0.5 ULP).
The observed average speed increase was 130x.
Checking 36240 known randomly found previously-slow-path acos inputs
shows 42 calls with incorrectly rounded results, with a maximum error of
0.500000008 ULP (for 0x1.f63845056f35ep-1). The previous "exact"
slow-path code showed 34 calls with incorrectly rounded results, with the
same maximum error of 0.500000008 ULP (for 0x1.f63845056f35ep-1).
The observed average speed increase was 130x.
The functions could likely be trimmed more while keeping acceptable
accuracy, but this at least gets rid of the egregiously slow cases.
Tested on x86_64.
The tls.h inclusion is not really required and limits possible
definition on more arch specific headers.
This is a cleanup to allow inline functions on sysdep.h, more
specifically on i386 and ia64 which requires to access some tls
definitions its own.
No semantic changes expected, checked with a build against all
affected ABIs.
In TS 18661-1, getpayload had an unspecified return value for a
non-NaN argument, while C2x requires the return value -1 in that case.
This patch implements the return value of -1. I don't think this is
worth having a new symbol version that's an alias of the old one,
although occasionally we do that in such cases where the new function
semantics are a refinement of the old ones (to avoid programs relying
on the new semantics running on older glibc versions but not behaving
as intended).
Tested for x86_64 and x86; also ran math/ tests for aarch64 and
powerpc.
This patch changes the exp10f error handling semantics to only set
errno according to POSIX rules. New symbol version is introduced at
GLIBC_2.32. The old wrappers are kept for compat symbols.
There are some outliers that need special handling:
- ia64 provides an optimized implementation of exp10f that uses ia64
specific routines to set SVID compatibility. The new symbol version
is aliased to the exp10f one.
- m68k also provides an optimized implementation, and the new version
uses it instead of the sysdeps/ieee754/flt32 one.
- riscv and csky uses the generic template implementation that
does not provide SVID support. For both cases a new exp10f
version is not added, but rather the symbols version of the
generic sysdeps/ieee754/flt32 is adjusted instead.
Checked on aarch64-linux-gnu, x86_64-linux-gnu, i686-linux-gnu,
powerpc64le-linux-gnu.
It is inspired by expf and reuses its tables and internal functions.
The error checks are inlined and errno setting is in separate tail
called functions, but the wrappers are kept in this patch to handle
the _LIB_VERSION==_SVID_ case.
Double precision arithmetics is used which is expected to be faster on
most targets (including soft-float) than using single precision and it
is easier to get good precision result with it.
Result for x86_64 (i7-4790K CPU @ 4.00GHz) are:
Before new code:
"exp10f": {
"workload-spec2017.wrf (adapted)": {
"duration": 4.0414e+09,
"iterations": 1.00128e+08,
"reciprocal-throughput": 26.6818,
"latency": 54.043,
"max-throughput": 3.74787e+07,
"min-throughput": 1.85038e+07
}
With new code:
"exp10f": {
"workload-spec2017.wrf (adapted)": {
"duration": 4.11951e+09,
"iterations": 1.23968e+08,
"reciprocal-throughput": 21.0581,
"latency": 45.4028,
"max-throughput": 4.74876e+07,
"min-throughput": 2.20251e+07
}
Result for aarch64 (A72 @ 2GHz) are:
Before new code:
"exp10f": {
"workload-spec2017.wrf (adapted)": {
"duration": 4.62362e+09,
"iterations": 3.3376e+07,
"reciprocal-throughput": 127.698,
"latency": 149.365,
"max-throughput": 7.831e+06,
"min-throughput": 6.69501e+06
}
With new code:
"exp10f": {
"workload-spec2017.wrf (adapted)": {
"duration": 4.29108e+09,
"iterations": 6.6752e+07,
"reciprocal-throughput": 51.2111,
"latency": 77.3568,
"max-throughput": 1.9527e+07,
"min-throughput": 1.29271e+07
}
Checked on x86_64-linux-gnu, powerpc64le-linux-gnu, aarch64-linux-gnu,
and sparc64-linux-gnu.
This came to light when adding hard-flaot support to ARC glibc port
without hardware sqrt support causing glibc build to fail:
| ../sysdeps/ieee754/dbl-64/e_sqrt.c: In function '__ieee754_sqrt':
| ../sysdeps/ieee754/dbl-64/e_sqrt.c:58:54: error: unused variable 'ty' [-Werror=unused-variable]
| double y, t, del, res, res1, hy, z, zz, p, hx, tx, ty, s;
The reason being EMULV() macro uses the hardware provided
__builtin_fma() variant, leaving temporary variables 'p, hx, tx, hy, ty'
unused hence compiler warning and ensuing error.
The intent of the patch was to fix that error, but EMULV is pervasive
and used fair bit indirectly via othe rmacros, hence this patch.
Functionally it should not result in code gen changes and if at all
those would be better since the scope of those temporaries is greatly
reduced now
Built tested with aarch64-linux-gnu arm-linux-gnueabi arm-linux-gnueabihf hppa-linux-gnu x86_64-linux-gnu arm-linux-gnueabihf riscv64-linux-gnu-rv64imac-lp64 riscv64-linux-gnu-rv64imafdc-lp64 powerpc-linux-gnu microblaze-linux-gnu nios2-linux-gnu hppa-linux-gnu
Also as suggested by Joseph [1] used --strip and compared the libs with
and w/o patch and they are byte-for-byte unchanged (with gcc 9).
| for i in `find . -name libm-2.31.9000.so`;
| do
| echo $i; diff $i /SCRATCH/vgupta/gnu2/install/glibcs/$i ; echo $?;
| done
| ./aarch64-linux-gnu/lib64/libm-2.31.9000.so
| 0
| ./arm-linux-gnueabi/lib/libm-2.31.9000.so
| 0
| ./x86_64-linux-gnu/lib64/libm-2.31.9000.so
| 0
| ./arm-linux-gnueabihf/lib/libm-2.31.9000.so
| 0
| ./riscv64-linux-gnu-rv64imac-lp64/lib64/lp64/libm-2.31.9000.so
| 0
| ./riscv64-linux-gnu-rv64imafdc-lp64/lib64/lp64/libm-2.31.9000.so
| 0
| ./powerpc-linux-gnu/lib/libm-2.31.9000.so
| 0
| ./microblaze-linux-gnu/lib/libm-2.31.9000.so
| 0
| ./nios2-linux-gnu/lib/libm-2.31.9000.so
| 0
| ./hppa-linux-gnu/lib/libm-2.31.9000.so
| 0
| ./s390x-linux-gnu/lib64/libm-2.31.9000.so
[1] https://sourceware.org/pipermail/libc-alpha/2019-November/108267.html
The minimum GCC version has been raised to 6.2 for building
glibc. Therefore, follow the advice inside the implementation
and remove the GCC < 6 codepath.
Likewise, remove the hidden_proto as all internal usages should
inline now.
GCC 7.5.0 (PR94200) will refuse to compile if both -mabi=% and
-mlong-double-128 are passed on the command line. Surprisingly,
it will work happily if the latter is not. For the sake of
maintaining status quo, test for and blacklist such compilers.
Tested with a GCC 8.3.1 and GCC 7.5.0 compiler for ppc64le.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
Improve the commentary to aid future developers who will stumble
upon this novel, yet not always perfect, mechanism to support
alternative formats for long double.
Likewise, rename __LONG_DOUBLE_USES_FLOAT128 to
__LDOUBLE_REDIRECTS_TO_FLOAT128_ABI now that development work
has settled down. The command used was
git grep -l __LONG_DOUBLE_USES_FLOAT128 ':!./ChangeLog*' | \
xargs sed -i 's/__LONG_DOUBLE_USES_FLOAT128/__LDOUBLE_REDIRECTS_TO_FLOAT128_ABI/g'
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
The test for enabling _Float128 or IEEE 128 long double can be
greatly simplified knowing that there is no ibm128, thus we require
no special cases, and everything is canonical.
This reverts the changes to ldbl-128ibm iscanonical.h from commit
8dbfea3a20 and extends the check
for __NO_LONG_DOUBLE_MATH to include a check for float128 redirects
to long double.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
This better resembles the default linking process with the gnulibs,
and also resolves the increasingly difficult to maintain
f128-loader-link usage on powerpc64le as some libgcc symbols are
dependent on those found in the loader (ld).
Tweak the PLT bypass magic when building glibc with long double
redirects. This is made more difficult by the fact we only get
one chance to redirect functions. This happens via the public
headers.
There are roughly three classes of redirect we need to attend to
today:
1. Simple redirects, redirected via cdef macro overrides and
and new libc_hidden_ldbl_proto macro.
2. Internal usage of internal API, e.g __snprintf, which has
no direct analogue. This is bypassed directly on case-by-
case basis.
3. Double redirects, e.g sscanf and related. These require
a heavier handed approach of macro renaming to existing
symbols.
Most simple redirects are handled via 1. Ideally, the libc_*
macro would live in libc-symbols.h, but in practice the macros
needed for it to do anything useful live in cdefs.h, so they
are defined in the local override.
Notably, the internal name of the asprintf generated for ieee ldbl
redirects is renamed to work with internal prefixed usage.
This resolves the local plt usage introduced when building glibc
with ldbl == ieee128 on ppc64le.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
With mathinline removal there is no need to keep building and testing
inline math tests.
The gen-libm-tests.py support to generate ULP_I_* is removed and all
libm-test-ulps files are updated to longer have the
i{float,double,ldouble} entries. The support for no-test-inline is
also removed from both gen-auto-libm-tests and the
auto-libm-test-out-* were regenerated.
Checked on x86_64-linux-gnu and i686-linux-gnu.
Soon, powerpc64le will need to provide extra compiler flags to the long
double files in order to continue to build using the IBM 128-bit
extended floating point type as long double.
This patch creates test-ibm128* tests from the long double function tests.
In order to explicitly test IBM long double functions -mabi=ibmlongdouble is
added to CFLAGS.
Likewise, update the test headers to correct choose ULPs when redirects
are enabled.
Co-authored-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
Co-authored-by: Paul E. Murphy <murphyp@linux.vnet.ibm.com>
For lack of a more comprehensive solution, tack on the ibm128 ABI
compiler options for the totalorder{,mag}l compat tests which exist
prior to enabling this feature.
The functions in the nexttoward family are special, in the sense that
they always have a long double argument, regardless of their suffix
(i.e.: nexttowardf and nexttoward have a long double argument, besides
the float and double arguments).
On top of that, they are also special because nexttoward functions are
not part of the _FloatN API, hence __nexttowardf128 do not exist.
This patch adds 4 new function implementations for the new long double
format:
__nexttoward_to_ieee128
__nexttowardf_to_ieee128
__nexttowardieee128 (as an alias to __nextafterieee128)
Likewise, rename "long double" "_Float128" in shared ldbl-128
files to ensure correct type is used irrespective of ABI
switches.
Thank you to those who helped out with this patch:
Co-Authored-By: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
Modify the headers to redirect long double functions to global __*f128
symbols or to __*ieee128 otherwise.
Most of the functions in math.h benefit from the infrastructure already
available for __LDBL_COMPAT. The only exceptions are nexttowardf and
nexttoward that need especial treatment.
Both math/bits/mathcalls-helper-functions.h and math/bits/mathcalls.h
were modified in order to provide alternative redirection destinations
that are essential to support functions that should not be redirected to
the same name pattern of the rest of the functions, i.e.: __fpclassify,
__signbit, __iseqsig, __issignaling, isinf, finite and isnan, which will
be redirected to __*f128 instead of __*ieee128 used for the rest.
Instead of attempting something more creative, just copy
the small struct from ldbl-128 and enable it when IEEE
long double is present, and update the ibm long double
variant if supported.
Likewise, provide a shadow copy of math_ldbl.h to prevent
the ibm128 specific long double header from poisoning
unrelated files due to it's usage in math_private.h.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
We want to ensure that if a second file is built to support
ieee128 long double, we built its companion implementation
with ibm128 long double. The shared object versions of these
files build correctly because the aliasing is sufficiently
complex to prevent the redirects from applying when defining
them.
However, this does not prevent the static object variants
from becoming quietly broken due to redirects. This is
intentionally avoided by marking such objects to be built
with -mabi=ibmlongdouble.
Shuffle the misplaced routines to build against the subdir
which defines the needed symbols.
A number of utility files and helper objects should also be
explicitly configured to build with the ibm128 ABI to prevent
gremlins when enabling IEEE long double.
Move the narrow math aliasing macros into a new sysdep header file
math-narrow-alias-float128.h. Then, provide an override header
to supply the necessary changes to supply the *ieee128 aliases of
these symbols.
This adds ieee128 aliases for faddl, fdivl, fmull, fsubl, daddl, ddivl,
dmull, dsubl.
After defining the long double redirections to double, __MATHDECL_1 has
to be redefined to its previous state in order to avoid redirecting all
subsequent types.
Reuse the template in order to provide the redirect for
scalbl to __scalbieee128, but avoid any extra aliasing
as this is intended to support long double redirects only.
This is a preparatory patch to enable building a _Float128
variant to ease reuse when building a _Float128 variant to
alias this long double only symbol.
Notably, stubs are added where missing to the native _Float128
sysdep dir to prevent building these newly templated variants
created inside the build directories.
Also noteworthy are the changes around LIBM_SVID_COMPAT. These
changes are not intuitive. The templated version is only
enabled when !LIBM_SVID_COMPAT, and the compat version is
predicated entirely on LIBM_SVID_COMPAT. Thus, exactly one is
stubbed out entirely when building. The nldbl scalb compat
files are updated to account for this.
Likewise, fixup the reuse of m68k's e_scalb{f,l}.c to include
it's override of e_scalb.c. Otherwise, the search path finds
the templated copy in the build directory. This could be
futher simplified by providing an overridden template, but I
lack the hardware to verify.
A recent discussion in bug 14469 notes that a threshold in float
Bessel function implementations, used to determine when to use a
simpler implementation approach, results in substantially inaccurate
results.
As I discussed in
<https://sourceware.org/ml/libc-alpha/2013-03/msg00345.html>, a
heuristic argument suggests 2^(S+P) as the right order of magnitude
for a suitable threshold, where S is the number of significand bits in
the floating-point type and P is the number of significant bits in the
representation of the floating-point type, and the float and ldbl-96
implementations use thresholds that are too small. Some threshold
does need using, there or elsewhere in the implementation, to avoid
spurious underflow and overflow for large arguments.
This patch sets the thresholds in the affected implementations to more
heuristically justifiable values. Results will still be inaccurate
close to zeroes of the functions (thus this patch does *not* fix any
of the bugs for Bessel function inaccuracy); fixing that would require
a different implementation approach, likely along the lines described
in <http://www.cl.cam.ac.uk/~jrh13/papers/bessel.ps.gz>.
So the justification for a change such as this would be statistical
rather than based on particular tests that had excessive errors and no
longer do so (no doubt such tests could be found, but would probably
be too fragile to add to the testsuite, as liable to give large errors
again from very small implementation changes or even from compiler
changes). See
<https://sourceware.org/ml/libc-alpha/2020-02/msg00638.html> for such
statistics of the resulting improvements for float functions.
Tested (glibc testsuite) for x86_64.
Bug 25487 reports stack corruption in ldbl-96 sinl on a pseudo-zero
argument (an representation where all the significand bits, including
the explicit high bit, are zero, but the exponent is not zero, which
is not a valid representation for the long double type).
Although this is not a valid long double representation, existing
practice in this area (see bug 4586, originally marked invalid but
subsequently fixed) is that we still seek to avoid invalid memory
accesses as a result, in case of programs that treat arbitrary binary
data as long double representations, although the invalid
representations of the ldbl-96 format do not need to be consistently
handled the same as any particular valid representation.
This patch makes the range reduction detect pseudo-zero and unnormal
representations that would otherwise go to __kernel_rem_pio2, and
returns a NaN for them instead of continuing with the range reduction
process. (Pseudo-zero and unnormal representations whose unbiased
exponent is less than -1 have already been safely returned from the
function before this point without going through the rest of range
reduction.) Pseudo-zero representations would previously result in
the value passed to __kernel_rem_pio2 being all-zero, which is
definitely unsafe; unnormal representations would previously result in
a value passed whose high bit is zero, which might well be unsafe
since that is not a form of input expected by __kernel_rem_pio2.
Tested for x86_64.
This should be unconditionally set to match the common implementation,
and fixes multiple test failures related to sprintf.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
The build has been failing on powerpc64le-linux-gnu with GCC 10
due to a maybe-uninitialized error:
../sysdeps/ieee754/dbl-64/mpa.c:875:6: error: ‘w.e’ may be used
uninitialized in this function [-Werror=maybe-uninitialized]
875 | EY -= EX;
| ^~
The warning is thrown because when __inv is called by __dvd *y is not
initialized and if t == 0 before calling __dbl_mp, EY will stay
uninitialized, as the function does not touch it in this case.
However, since t will be set to 1/t before calling __dbl_mp, t == 0 will
never happen, so we can instruct the compiler to ignore this case, which
suppresses the warning.
Tested on powerpc64le.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
This patch adds a new macro, libm_alias_finite, to define all _finite
symbol. It sets all _finite symbol as compat symbol based on its first
version (obtained from the definition at built generated first-versions.h).
The <fn>f128_finite symbols were introduced in GLIBC 2.26 and so need
special treatment in code that is shared between long double and float128.
It is done by adding a list, similar to internal symbol redifinition,
on sysdeps/ieee754/float128/float128_private.h.
Alpha also needs some tricky changes to ensure we still emit 2 compat
symbols for sqrt(f).
Passes buildmanyglibc.
Co-authored-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Reviewed-by: Siddhesh Poyarekar <siddhesh@sourceware.org>
Some compiler versions, e.g. GCC 7, complain when -mlong-double-128 is
used together with -mabi=ibmlongdouble or -mabi=ieeelongdouble,
producing the following error message:
cc1: error: ‘-mabi=ibmlongdouble’ requires ‘-mlong-double-128’
This patch removes -mlong-double-128 from the compilation lines that
explicitly request -mabi=*longdouble.
Tested for powerpc64le.
Reviewed-by: Tulio Magno Quites Machado Filho <tuliom@linux.ibm.com>
Some of the files that provide stdio.h and wchar.h functions have a
filename prefixed with 'io', such as 'iovsprintf.c'. On platforms that
imply ldbl-128ibm-compat, these files must be compiled with the flag
-mabi=ibmlongdouble. This patch adds this flag to their compilation.
Notice that this is not required for the other files that provide
similar functions, because filenames that are not prefixed with 'io'
have ldbl-128ibm-compat counterparts in the Makefile, which already adds
-mabi=ibmlongdouble to them.
Reviewed-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
On platforms where long double has IEEE binary128 format as a third
option (initially, only powerpc64le), many exported functions are
redirected to their __*ieee128 equivalents. This redirection is
provided by installed headers such as stdio-ldbl.h, and is supposed to
work correctly with user code.
However, during the build of glibc, similar redirections are employed,
in internal headers, such as include/stdio.h, in order to avoid extra
PLT entries. These redirections conflict with the redirections to
__*ieee128, and must be avoided during the build. This patch protects
the second redirections with a test for __LONG_DOUBLE_USES_FLOAT128, a
new macro that is defined to 1 when functions that deal with long double
typed values reuses the _Float128 implementation (this is currently only
true for powerpc64le).
Tested for powerpc64le, x86_64, and with build-many-glibcs.py.
Co-authored-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
Reviewed-by: Florian Weimer <fweimer@redhat.com>
On powerpc64le, the libm_alias_float128_other_r_ldbl macro is
used to create an alias between totalorderf128 and __totalorderlieee128,
as well as between the totalordermagf128 and __totalordermaglieee128.
However, the totalorder* and totalordermag* functions changed their
parameter type since commit ID 42760d7646 and got compat symbols for
their old versions. With this change, the aforementioned macro would
create two conflicting aliases for __totalorderlieee128 and
__totalordermaglieee128.
This patch avoids the creation of the alias between the IEEE long double
symbols (__totalorderl*ieee128) and the compat symbols, because the IEEE
long double functions have never been exported thus don't need such
compat symbol.
Tested for powerpc64le.
Reviewed-by: Joseph Myers <joseph@codesourcery.com>
This patch adds IEEE long double versions of q*cvt* functions for
powerpc64le. Unlike all other long double to/from string conversion
functions, these do not rely on internal functions that can take
floating-point numbers with different formats and act on them
accordingly, instead, the related files are rebuilt with the
-mabi=ieeelongdouble compiler flag set.
Having -mabi=ieeelongdouble passed to the compiler causes the object
files to be marked with a .gnu_attribute that is incompatible with the
.gnu_attribute in files built with -mabi=ibmlongdouble (the default).
The difference causes error messages similar to the following:
ld: libc_pic.a(s_isinfl.os) uses IBM long double,
libc_pic.a(ieee128-qefgcvt_r.os) uses IEEE long double.
collect2: error: ld returned 1 exit status
make[2]: *** [../Makerules:649: libc_pic.os] Error 1
Although this warning is useful in other situations, the library
actually needs to have functions with different long double formats, so
.gnu_attribute generation is explicitly disabled for these files with
the use of -mno-gnu-attribute.
Tested for powerpc64le on the branch that actually enables the
sysdeps/ieee754/ldbl-128ibm-compat for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
In the format string for *scanf functions, the '%as', '%aS', and '%a[]'
modifiers behave differently depending on ISO C99 compatibility. When
_GNU_SOURCE is defined and -std=c89 is passed to the compiler, these
functions behave like ascanf, and the modifiers allocate memory for the
output. Otherwise, the ISO C99 compliant version of these functions is
used, and the modifiers consume a floating-point argument. This patch
adds the IEEE binary128 variant of ISO C99 compliant functions for the
third long double format on powerpc64le.
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Since commit
commit 03992356e6
Author: Zack Weinberg <zackw@panix.com>
Date: Sat Feb 10 11:58:35 2018 -0500
Use C99-compliant scanf under _GNU_SOURCE with modern compilers.
the selection of the GNU versions of scanf functions requires both
_GNU_SOURCE and -std=c89. This patch changes the tests in
ldbl-128ibm-compat so that they actually test the GNU versions (without
this change, the redirection to the ISO C99 version always happens, so
GNU versions of the new implementation (e.g. __scanfieee128) were left
untested).
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
This patch just adjusts the generic implementation regarding code style.
No functional change.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch just adjusts the generic implementation regarding code style.
No functional change.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch just adjusts the generic implementation regarding code style.
No functional change.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch just adjusts the generic implementation regarding code style.
No functional change.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch just adjusts the generic implementation regarding code style.
No functional change.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is always using the corresponding GCC builtin for copysignf, copysign,
and is using the builtin for copysignl, copysignf128 if the USE_FUNCTION_BUILTIN
macros are defined to one in math-use-builtins.h.
Altough the long double version is enabled by default we still need
the macro and the alternative implementation as the _Float128 version
of the builtin is not available with all supported GCC versions.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for roundf, round,
roundl and roundf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for truncf, trunc,
truncl and truncf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for ceilf, ceil,
ceill and ceilf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for floorf, floor,
floorl and floorf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for rintf, rint,
rintl and rintf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch is using the corresponding GCC builtin for nearbyintf, nearbyint,
nearbintl and nearbyintf128 if the USE_FUNCTION_BUILTIN macros are defined to one
in math-use-builtins.h.
This is the case for s390 if build with at least --march=z196 --mzarch.
Otherwise the generic implementation is used. The code of the generic
implementation is not changed.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_round.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_trunc.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
The code is not changed except changes in code style.
Also adjusted the include path in x86_64 and sparc64 files.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_ceil.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
The code is not changed except changes in code style.
Also adjusted the include path in x86_64 and sparc64 files.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_floor.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
The code is not changed except changes in code style.
Also adjusted the include path in x86_64 and sparc64 files.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_rint.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
The code is not changed except changes in code style.
Also adjusted the include path in x86_64 file.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
This patch replaces s_nearbyint.c in sysdeps/dbl-64 with the one in
sysdeps/dbl-64/wordsize-64 and removes the latter one.
The code is not changed except changes in code style.
Also adjusted the include path in x86_64 file.
Reviewed-by: Adhemerval Zanella <adhemerval.zanella@linaro.org>
Since the commit
commit 86a0f56158
Author: Rajalakshmi Srinivasaraghavan <raji@linux.vnet.ibm.com>
Date: Thu Jun 28 13:57:50 2018 +0530
ldbl-128ibm-compat: Introduce ieee128 symbols
IEEE long double versions of strfroml, strtold, and wcstold have been
prepared, but not exposed (which will only happen when the full support
for IEEE long double is complete). This patch adds tests for these
functions in both IBM and IEEE long double mode.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
This patch adds elementary tests to check that strfmon and strfmon_l
correctly evaluate long double values with IBM Extended Precision and
IEEE binary128 format.
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Similarly to what has been done for printf-like functions, more
specifically to the internal implementation in __vfprintf_internal, this
patch extends __vstrfmon_l_internal to deal with long double values with
binary128 format (as a third format option and reusing the float128
implementation).
Tested for powerpc64le, powerpc64, x86_64, and with build-many-glibcs.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Several commits to the ldbl-128ibm-compat directory added new files
where the URL in the copyright notice pointed to an http, rather than to
an https, address. This happened because I copied the notices before
commit ID 5a82c74822. This trivial patch fixes this issue.
Similarly to __vfprintf_internal and __vfscanf_internal, the internal
implementation of syslog functions (__vsyslog_internal) takes a
'mode_flags' parameter used to select the format of long double
parameters. This patch adds variants of the syslog functions that set
'mode_flags' to PRINTF_LDBL_USES_FLOAT128, thus enabling the correct
printing of long double values on powerpc64le, when long double has IEEE
binary128 format (-mabi=ieeelongdouble).
Tested for powerpc64le.
Reviewed-by: Florian Weimer <fweimer@redhat.com>
Reviewed-by: Joseph Myers <joseph@codesourcery.com>
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Similarly to the functions from the *printf family, this patch adds
implementations for __obstack_*printf* functions that set the
'mode_flags' parameter to PRINTF_LDBL_USES_FLOAT128, before making calls
to __vfprintf_internal (indirectly through __obstack_vprintf_internal).
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Commit IDs 9771e6cb51 and 7597b0c7f7 added tests for the functions
from err.h and error.h that can take long double parameters.
Afterwards, commit ID f0eaf86276 reused them on architectures that
changed the long double format from the same as double to something else
(i.e.: architectures that imply ldbl-opt). This patch reuses it again
for IEEE long double on powerpc64le.
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Use the recently added, internal functions, __error_at_line_internal and
__error_internal, to provide error.h functions that can take long double
arguments with IEEE binary128 format on platforms where long double can
also take double format or some non-IEEE format (currently, this means
powerpc64le).
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Use the recently added, internal functions, __vwarnx_internal and
__vwarn_internal, to provide err.h functions that can take long double
arguments with IEEE binary128 format on platforms where long double can
also take double format or some non-IEEE format (currently, this means
powerpc64le).
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Use the recently added, internal functions, __argp_error_internal and
__argp_failure_internal, to provide argp_error and argp_failure that can
take long double arguments with IEEE binary128 format on platforms where
long double can also take double format or some non-IEEE format
(currently, this means powerpc64le).
Tested for powerpc64le.
Reviewed-by: Paul E. Murphy <murphyp@linux.ibm.com>
Similarly to what was done for regular character scanning functions,
this patch uses the new mode mask, SCANF_LDBL_USES_FLOAT128, in the
'mode' argument of the wide characters scanning function,
__vfwscanf_internal (which is also extended to support scanning
floating-point values with IEEE binary128, by redirecting calls to
__wcstold_internal to __wcstof128_internal).
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
The 'mode' argument to __vfscanf_internal allows the selection of the
long double format for all long double arguments requested by the format
string. Currently, there are two possibilities: long double with the
same format as double or long double as something else. The 'something
else' format varies between architectures, and on powerpc64le, it means
IBM Extended Precision format.
In preparation for the third option of long double format on
powerpc64le, this patch uses the new mode mask,
SCANF_LDBL_USES_FLOAT128, which tells __vfscanf_internal to call
__strtof128_internal, instead of __strtold_internal, and save the output
into a _Float128 variable.
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
The format string can request positional parameters, instead of relying
on the order in which they appear as arguments. Since this has an
effect on how the type of each argument is determined, this patch
extends the test cases to use positional parameters with mixed double
and long double types, to verify that the IEEE long double
implementations of *printf work correctly in this scenario.
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
A single format string can take double and long double parameters at the
same time. Internally, these parameters are routed to the same
function, which correctly reads them and calls the underlying functions
responsible for the actual conversion to string. This patch adds a new
case to test this scenario.
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
Similarly to what was done for the regular character, fortified printing
functions, this patch combines the mode masks PRINTF_LDBL_USES_FLOAT128
and PRINTF_FORTIFY to provide wide character versions of fortified
printf functions. It also adds two flavors of test cases: one that
explicitly calls the fortified functions, and another that reuses the
non-fortified test, but defining _FORTIFY_SOURCE as 2. The first
guarantees that the implementations are actually being tested
(independently of what's in bits/wchar2.h), whereas the second
guarantees that the redirections calls the correct function in the IBM
and IEEE long double cases.
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
Since the introduction of internal functions with explicit flags for the
printf family of functions, the 'mode' parameter can be used to select
which format long double parameters have (with the mode flags:
PRINTF_LDBL_IS_DBL and PRINTF_LDBL_USES_FLOAT128), as well as to select
whether to check for overflows (mode flag: PRINTF_FORTIFY).
This patch combines PRINTF_LDBL_USES_FLOAT128 and PRINTF_FORTIFY to
provide the IEEE binary128 version of printf-like function for platforms
where long double can take this format, in addition to the double format
and to some non-ieee format (currently, this means powerpc64le).
There are two flavors of test cases provided with this patch: one that
explicitly calls the fortified functions, for instance __asprintf_chk,
and another that reuses the non-fortified test, but defining
_FORTIFY_SOURCE as 2. The first guarantees that the implementations are
actually being tested (in bits/stdio2.h, vprintf gets redirected to
__vfprintf_chk, which would leave __vprintf_chk untested), whereas the
second guarantees that the redirections calls the correct function in
the IBM and IEEE long double cases.
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
Similarly to what was done for regular character printing functions,
this patch uses the new mode mask, PRINTF_LDBL_USES_FLOAT128, in the
'mode' argument of the wide characters printing function,
__vfwprintf_internal (which is also extended to support printing
floating-point values with IEEE binary128, by saving floating-point
values into variables of type __float128 and adjusting the parameters to
__printf_fp and __printf_fphex as if it was a call from a wide-character
version of strfromf128 (even though such version does not exist)).
Tested for powerpc64le.
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
The 'mode' argument to __vfprintf_internal allows the selection of the
long double format for all long double arguments requested by the format
string. Currently, there are two possibilities: long double with the
same format as double or long double as something else. The 'something
else' format varies between architectures, and on powerpc64le, it means
IBM Extended Precision format.
In preparation for the third option of long double format on
powerpc64le, this patch uses the new mode mask,
PRINTF_LDBL_USES_FLOAT128, which tells __vfprintf_internal to save the
floating-point values into variables of type __float128 and adjusts the
parameters to __printf_fp and __printf_fphex as if it was a call from
strfromf128.
Many files from the stdio-common, wcsmbs, argp, misc, and libio
directories will have IEEE binary128 counterparts. Setting the correct
compiler options to these files (original and counterparts) would
produce a large amount of repetitive Makefile rules. To avoid this
repetition, this patch adds a Makefile routine that iterates over the
files adding or removing the appropriate flags.
Tested for powerpc64le.
Reviewed-By: Florian Weimer <fweimer@redhat.com>
Reviewed-By: Joseph Myers <joseph@codesourcery.com>
Reviewed-By: Paul E. Murphy <murphyp@linux.ibm.com>
Very recent commit 854e91bf6b enabled
inline of issignalingf() in general (__issignalingf in include/math.h).
There is another implementation for an inline use of issignalingf
(issignalingf_inline in sysdeps/ieee754/flt-32/math_config.h)
which could instead make use of the new enablement.
Replace the use of issignalingf_inline with __issignaling. Using
issignaling (instead of __issignalingf) will allow future enhancements
to the type-generic implementation, issignaling, to be automatically
adopted.
The implementations are slightly different, and compile to slightly
different code, but I measured no significant performance difference.
The second implementation was brought to my attention by:
Suggested-by: Joseph Myers <joseph@codesourcery.com>
Reviewed-by: Joseph Myers <joseph@codesourcery.com>
With only two exceptions (sys/types.h and sys/param.h, both of which
historically might have defined BYTE_ORDER) the public headers that
include <endian.h> only want to be able to test __BYTE_ORDER against
__*_ENDIAN.
This patch creates a new bits/endian.h that can be included by any
header that wants to be able to test __BYTE_ORDER and/or
__FLOAT_WORD_ORDER against the __*_ENDIAN constants, or needs
__LONG_LONG_PAIR. It only defines macros in the implementation
namespace.
The existing bits/endian.h (which could not be included independently
of endian.h, and only defines __BYTE_ORDER and maybe __FLOAT_WORD_ORDER)
is renamed to bits/endianness.h. I also took the opportunity to
canonicalize the form of this header, which we are stuck with having
one copy of per architecture. Since they are so short, this means git
doesn’t understand that they were renamed from existing headers, sigh.
endian.h itself is a nonstandard header and its only remaining use
from a standard header is guarded by __USE_MISC, so I dropped the
__USE_MISC conditionals from around all of the public-namespace things
it defines. (This means, an application that requests strict library
conformance but includes endian.h will still see the definition of
BYTE_ORDER.)
A few changes to specific bits/endian(ness).h variants deserve
mention:
- sysdeps/unix/sysv/linux/ia64/bits/endian.h is moved to
sysdeps/ia64/bits/endianness.h. If I remember correctly, ia64 did
have selectable endianness, but we have assembly code in
sysdeps/ia64 that assumes it’s little-endian, so there is no reason
to treat the ia64 endianness.h as linux-specific.
- The C-SKY port does not fully support big-endian mode, the compile
will error out if __CSKYBE__ is defined.
- The PowerPC port had extra logic in its bits/endian.h to detect a
broken compiler, which strikes me as unnecessary, so I removed it.
- The only files that defined __FLOAT_WORD_ORDER always defined it to
the same value as __BYTE_ORDER, so I removed those definitions.
The SH bits/endian(ness).h had comments inconsistent with the
actual setting of __FLOAT_WORD_ORDER, which I also removed.
- I *removed* copyright boilerplate from the few bits/endian(ness).h
headers that had it; these files record a single fact in a fashion
dictated by an external spec, so I do not think they are copyrightable.
As long as I was changing every copy of ieee754.h in the tree, I
noticed that only the MIPS variant includes float.h, because it uses
LDBL_MANT_DIG to decide among three different versions of
ieee854_long_double. This patch makes it not include float.h when
GCC’s intrinsic __LDBL_MANT_DIG__ is available.
* string/endian.h: Unconditionally define LITTLE_ENDIAN,
BIG_ENDIAN, PDP_ENDIAN, and BYTE_ORDER. Condition byteswapping
macros only on !__ASSEMBLER__. Move the definitions of
__BIG_ENDIAN, __LITTLE_ENDIAN, __PDP_ENDIAN, __FLOAT_WORD_ORDER,
and __LONG_LONG_PAIR to...
* string/bits/endian.h: ...this new file, which includes
the renamed header bits/endianness.h for the definition of
__BYTE_ORDER and possibly __FLOAT_WORD_ORDER.
* string/Makefile: Install bits/endianness.h.
* include/bits/endian.h: New wrapper.
* bits/endian.h: Rename to bits/endianness.h.
Add multiple-include guard. Rewrite the comment explaining what
the machine-specific variants of this file should do.
* sysdeps/unix/sysv/linux/ia64/bits/endian.h:
Move to sysdeps/ia64.
* sysdeps/aarch64/bits/endian.h
* sysdeps/alpha/bits/endian.h
* sysdeps/arm/bits/endian.h
* sysdeps/csky/bits/endian.h
* sysdeps/hppa/bits/endian.h
* sysdeps/ia64/bits/endian.h
* sysdeps/m68k/bits/endian.h
* sysdeps/microblaze/bits/endian.h
* sysdeps/mips/bits/endian.h
* sysdeps/nios2/bits/endian.h
* sysdeps/powerpc/bits/endian.h
* sysdeps/riscv/bits/endian.h
* sysdeps/s390/bits/endian.h
* sysdeps/sh/bits/endian.h
* sysdeps/sparc/bits/endian.h
* sysdeps/x86/bits/endian.h:
Rename to endianness.h; canonicalize form of file; remove
redundant definitions of __FLOAT_WORD_ORDER.
* sysdeps/powerpc/bits/endianness.h: Remove logic to check for
broken compilers.
* ctype/ctype.h
* sysdeps/aarch64/nptl/bits/pthreadtypes-arch.h
* sysdeps/arm/nptl/bits/pthreadtypes-arch.h
* sysdeps/csky/nptl/bits/pthreadtypes-arch.h
* sysdeps/ia64/ieee754.h
* sysdeps/ieee754/ieee754.h
* sysdeps/ieee754/ldbl-128/ieee754.h
* sysdeps/ieee754/ldbl-128ibm/ieee754.h
* sysdeps/m68k/nptl/bits/pthreadtypes-arch.h
* sysdeps/microblaze/nptl/bits/pthreadtypes-arch.h
* sysdeps/mips/ieee754/ieee754.h
* sysdeps/mips/nptl/bits/pthreadtypes-arch.h
* sysdeps/nios2/nptl/bits/pthreadtypes-arch.h
* sysdeps/nptl/pthread.h
* sysdeps/riscv/nptl/bits/pthreadtypes-arch.h
* sysdeps/sh/nptl/bits/pthreadtypes-arch.h
* sysdeps/sparc/sparc32/ieee754.h
* sysdeps/unix/sysv/linux/generic/bits/stat.h
* sysdeps/unix/sysv/linux/generic/bits/statfs.h
* sysdeps/unix/sysv/linux/sys/acct.h
* wctype/bits/wctype-wchar.h:
Include bits/endian.h, not endian.h.
* sysdeps/unix/sysv/linux/hppa/pthread.h: Don’t include endian.h.
* sysdeps/mips/ieee754/ieee754.h: Use __LDBL_MANT_DIG__
in ifdefs, instead of LDBL_MANT_DIG. Only include float.h
when __LDBL_MANT_DIG__ is not predefined, in which case
define __LDBL_MANT_DIG__ to equal LDBL_MANT_DIG.
The resolution of C floating-point Clarification Request 25
<http://www.open-std.org/jtc1/sc22/wg14/www/docs/n2397.htm#dr_25> is
that the totalorder and totalordermag functions should take pointer
arguments, and this has been adopted in C2X (with const added; note
that the integration of this change into C2X is present in the C
standard git repository but postdates the most recent public PDF
draft).
This patch updates glibc accordingly. As a defect resolution, the API
is changed unconditionally rather than supporting any sort of TS
18661-1 mode for compilation with the old version of the API. There
are compat symbols for existing binaries that pass floating-point
arguments directly. As a consequence of changing to pointer
arguments, there are no longer type-generic macros in tgmath.h for
these functions.
Because of the fairly complicated logic for creating libm function
aliases and determining the set of aliases to create in a given glibc
configuration, rather than duplicating all that in individual source
files to create the versioned and compat symbols, the source files for
the various versions of totalorder functions are set up to redefine
weak_alias before using libm_alias_* macros to create the symbols
required. In turn, this requires creating a separate alias for each
symbol version pointing to the same implementation (see binutils bug
<https://sourceware.org/bugzilla/show_bug.cgi?id=23840>), which is
done automatically using __COUNTER__. (As I noted in
<https://sourceware.org/ml/libc-alpha/2018-10/msg00631.html>, it might
well make sense for glibc's symbol versioning macros to do that alias
creation with __COUNTER__ themselves, which would somewhat simplify
the logic in the totalorder source files.)
It is of course desirable to test the compat symbols. I did this with
the generic libm-test machinery, but didn't wish to duplicate the
actual tables of test inputs and outputs, and thought it risky to
attempt to have a single object file refer to both default and compat
versions of the same function in order to test them together. Thus, I
created libm-test-compat_totalorder.inc and
libm-test-compat_totalordermag.inc which include the generated .c
files (with the processed version of those tables of inputs) from the
non-compat tests, and added appropriate dependencies. I think this
provides sufficient test coverage for the compat symbols without also
needing to make the special ldbl-96 and ldbl-128ibm tests (of
peculiarities relating to the representations of those formats that
can't be covered in the generic tests) run for the compat symbols.
Tests of compat symbols need to be internal tests, meaning _ISOMAC is
not defined. Making some libm-test tests into internal tests showed
up two other issues. GCC diagnoses duplicate macro definitions of
__STDC_* macros, including __STDC_WANT_IEC_60559_TYPES_EXT__; I added
an appropriate conditional and filed
<https://gcc.gnu.org/bugzilla/show_bug.cgi?id=91451> for this issue.
On ia64, include/setjmp.h ends up getting included indirectly from
libm-symbols.h, resulting in conflicting definitions of the STR macro
(also defined in libm-test-driver.c); I renamed the macros in
include/setjmp.h. (It's arguable that we should have common internal
headers used everywhere for stringizing and concatenation macros.)
Tested for x86_64 and x86, and with build-many-glibcs.py.
* math/bits/mathcalls.h
[__GLIBC_USE (IEC_60559_BFP_EXT) || __MATH_DECLARING_FLOATN]
(totalorder): Take pointer arguments.
[__GLIBC_USE (IEC_60559_BFP_EXT) || __MATH_DECLARING_FLOATN]
(totalordermag): Likewise.
* manual/arith.texi (totalorder): Likewise.
(totalorderf): Likewise.
(totalorderl): Likewise.
(totalorderfN): Likewise.
(totalorderfNx): Likewise.
(totalordermag): Likewise.
(totalordermagf): Likewise.
(totalordermagl): Likewise.
(totalordermagfN): Likewise.
(totalordermagfNx): Likewise.
* math/tgmath.h (__TGMATH_BINARY_REAL_RET_ONLY): Remove macro.
[__GLIBC_USE (IEC_60559_BFP_EXT)] (totalorder): Likewise.
[__GLIBC_USE (IEC_60559_BFP_EXT)] (totalordermag): Likewise.
* math/Versions (GLIBC_2.31): Add totalorder, totalorderf,
totalorderl, totalordermag, totalordermagf, totalordermagl,
totalorderf32, totalorderf64, totalorderf32x, totalordermagf32,
totalordermagf64, totalordermagf32x, totalorderf64x,
totalordermagf64x, totalorderf128 and totalordermagf128.
* math/Makefile (libm-test-funcs-noauto): Add compat_totalorder
and compat_totalordermag.
(libm-test-funcs-compat): New variable.
(libm-tests-compat): Likewise.
(tests): Do not include compat tests.
(tests-internal): Add compat tests.
($(foreach t,$(libm-tests-base),
$(objpfx)$(t)-compat_totalorder.o)): Depend
on $(objpfx)libm-test-totalorder.c.
($(foreach t,$(libm-tests-base),
$(objpfx)$(t)-compat_totalordermag.o): Depend on
$(objpfx)libm-test-totalordermag.c.
(tgmath3-macros): Remove totalorder and totalordermag.
* math/libm-test-compat_totalorder.inc: New file.
* math/libm-test-compat_totalordermag.inc: Likewise.
* math/libm-test-driver.c (struct test_ff_i_data): Update comment.
(RUN_TEST_fpfp_b): New macro.
(RUN_TEST_LOOP_fpfp_b): Likewise.
* math/libm-test-totalorder.inc (totalorder_test_data): Use
TEST_fpfp_b.
(totalorder_test): Condition on [!COMPAT_TEST].
(do_test): Likewise.
* math/libm-test-totalordermag.inc (totalordermag_test_data): Use
TEST_fpfp_b.
(totalordermag_test): Condition on [!COMPAT_TEST].
(do_test): Likewise.
* math/gen-tgmath-tests.py (Tests.add_all_tests): Remove
totalorder and totalordermag.
* math/test-tgmath.c (NCALLS): Change to 132.
(F(compile_test)): Do not call totalorder or totalordermag.
(F(totalorder)): Remove.
(F(totalordermag)): Likewise.
* include/float.h (__STDC_WANT_IEC_60559_TYPES_EXT__): Do not
define if [__STDC_WANT_IEC_60559_TYPES_EXT__].
* include/setjmp.h [!_ISOMAC] (STR_HELPER): Rename to
SJSTR_HELPER.
[!_ISOMAC] (STR): Rename to SJSTR. Update call to STR_HELPER.
[!_ISOMAC] (TEST_SIZE): Update call to STR.
[!_ISOMAC] (TEST_ALIGN): Likewise.
[!_ISOMAC] (TEST_OFFSET): Likewise.
* sysdeps/ieee754/dbl-64/s_totalorder.c: Include <shlib-compat.h>
and <first-versions.h>.
(__totalorder): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/dbl-64/s_totalordermag.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalordermag): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/dbl-64/wordsize-64/s_totalorder.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalorder): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/dbl-64/wordsize-64/s_totalordermag.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalordermag): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/float128/float128_private.h
(__totalorder_compatl): New macro.
(__totalordermag_compatl): Likewise.
* sysdeps/ieee754/flt-32/s_totalorderf.c: Include <shlib-compat.h>
and <first-versions.h>.
(__totalorderf): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/flt-32/s_totalordermagf.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalordermagf): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/ldbl-128/s_totalorderl.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalorderl): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/ldbl-128/s_totalordermagl.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalordermagl): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/ldbl-128ibm/s_totalorderl.c: Include
<shlib-compat.h>.
(__totalorderl): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/ldbl-128ibm/s_totalordermagl.c: Include
<shlib-compat.h>.
(__totalordermagl): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/ldbl-96/s_totalorderl.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalorderl): Take pointer arguments. Add symbol versions and
compat symbols.
* sysdeps/ieee754/ldbl-96/s_totalordermagl.c: Include
<shlib-compat.h> and <first-versions.h>.
(__totalordermagl): Take pointer arguments. Add symbol versions
and compat symbols.
* sysdeps/ieee754/ldbl-opt/nldbl-totalorder.c (totalorderl): Take
pointer arguments.
* sysdeps/ieee754/ldbl-opt/nldbl-totalordermag.c (totalordermagl):
Likewise.
* sysdeps/ieee754/ldbl-128ibm/test-totalorderl-ldbl-128ibm.c
(do_test): Update calls to totalorderl and totalordermagl.
* sysdeps/ieee754/ldbl-96/test-totalorderl-ldbl-96.c (do_test):
Update calls to totalorderl and totalordermagl.
* sysdeps/mach/hurd/i386/libm.abilist: Update.
* sysdeps/unix/sysv/linux/aarch64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/alpha/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/arm/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/csky/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/hppa/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/i386/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/ia64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/m68k/coldfire/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/m68k/m680x0/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/microblaze/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/mips/mips32/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/mips/mips64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/nios2/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/powerpc/powerpc32/fpu/libm.abilist:
Likewise.
* sysdeps/unix/sysv/linux/powerpc/powerpc32/nofpu/libm.abilist:
Likewise.
* sysdeps/unix/sysv/linux/powerpc/powerpc64/be/libm.abilist:
Likewise.
* sysdeps/unix/sysv/linux/powerpc/powerpc64/le/libm.abilist:
Likewise.
* sysdeps/unix/sysv/linux/riscv/rv64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/s390/s390-32/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/s390/s390-64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/sh/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/sparc/sparc32/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/sparc/sparc64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/x86_64/64/libm.abilist: Likewise.
* sysdeps/unix/sysv/linux/x86_64/x32/libm.abilist: Likewise.
- The resulting binary difference on 32 bits architecture is
minimum. On i686-linux-gnu (with architecture optimization
routine removed) there is no different using logb benchtests
- It helps wordsize-64 architectures that use ldbl-opt.
- It add some code simplification with reduction of duplicated
implementations.
Checked on powerpc-linux-gnu (built without --with-cpu, with
--with-cpu=power4 and with --with-cpu=power5+ and --disable-multi-arch),
powerpc64-linux-gnu (built without --with-cp and with --with-cpu=power5+
and --disable-multi-arch).
* sysdeps/ieee754/dbl-64/wordsize-64/s_logb.c: Move to ...
* sysdeps/ieee754/dbl-64/s_logb.c: ... here. Add work around for
powerpc32 integer 0 converting to -0.
Reviewed-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
- math.h will use compiler builtin for gcc 4.4 when built without
-fsignaling-nans and the builtin is expanded inline for all
support architectures. As an example, there is no intra finite
call on libm for the architecture I checked, x86, arm, aarch64,
and powerpc.
- The resulting binary difference on 32 bits architecture is minimum
for the non hotspot symbol.
- It helps wordsize-64 architectures that use ldbl-opt.
- It add some code simplification with reduction of duplicated
implementations.
Checked on powerpc-linux-gnu (built without --with-cpu, with
--with-cpu=power4 and with --with-cpu=power5+ and --disable-multi-arch),
powerpc64-linux-gnu (built without --with-cp and with --with-cpu=power5+
and --disable-multi-arch).
* sysdeps/ieee754/dbl-64/wordsize-64/s_finite.c: Move to ...
* sysdeps/ieee754/dbl-64/s_finite.c: ... here and format code.
Reviewed-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
- math.h will use compiler builtin for gcc 4.4 when built without
-fsignaling-nans and the builtin is expanded inline for all
support architectures. As an example, there is no intra isinf
call on libm for the architecture I checked, x86, arm, aarch64,
and powerpc.
- The resulting binary difference on 32 bits architecture is minimum
for the non hotspot symbol.
- It helps wordsize-64 architectures that use ldbl-opt.
- It add some code simplification with reduction of duplicated
implementations.
Checked on powerpc-linux-gnu (built without --with-cpu, with
--with-cpu=power4 and with --with-cpu=power5+ and --disable-multi-arch),
powerpc64-linux-gnu (built without --with-cp and with --with-cpu=power5+
and --disable-multi-arch).
* sysdeps/ieee754/dbl-64/wordsize-64/s_isinf.c: Move to ...
* sysdeps/ieee754/dbl-64/s_isinf.c: ... here and format code.
Reviewed-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
- math.h will use compiler builtin for gcc 4.4 when built without
-fsignaling-nans and the builtin is expanded inline for all
support architectures. As an example, there is no intra isnan
call on libm for the architecture I checked, x86, arm, aarch64,
and powerpc.
- The resulting binary difference on 32 bits architecture is minimum
for the non hotspot symbol.
- It helps wordsize-64 architectures that use ldbl-opt.
- It add some code simplification with reduction of duplicated
implementations.
Checked on powerpc-linux-gnu (built without --with-cpu, with
--with-cpu=power4 and with --with-cpu=power5+ and --disable-multi-arch),
powerpc64-linux-gnu (built without --with-cp and with --with-cpu=power5+
and --disable-multi-arch).
* sysdeps/ieee754/dbl-64/wordsize-64/s_isnan.c: Move to ...
* sysdeps/ieee754/dbl-64/s_isnan.c: ... here and format code.
Reviewed-by: Gabriel F. T. Gomes <gabrielftg@linux.ibm.com>
Complementing commit 4a06ceea33 ("sysdeps/ieee754/soft-fp: ignore
maybe-uninitialized with -O [BZ #19444]") and commit 27c5e756a2
("sysdeps/ieee754: prevent maybe-uninitialized errors with -O [BZ
#19444]") also fix compilation errors observed at -O1 in `__ddivl' and
`__fdivl' with GCC 9 and RISC-V targets:
In file included from ../soft-fp/soft-fp.h:318,
from ../sysdeps/ieee754/soft-fp/s_fdivl.c:27:
../sysdeps/ieee754/soft-fp/s_fdivl.c: In function '__fdivl':
../soft-fp/op-2.h:108:9: error: 'R_f1' may be used uninitialized in this function [-Werror=maybe-uninitialized]
108 | : (X##_f1 << (2*_FP_W_TYPE_SIZE - (N)))) \
| ^
../sysdeps/ieee754/soft-fp/s_fdivl.c:37:14: note: 'R_f1' was declared here
37 | FP_DECL_Q (R);
| ^
../soft-fp/op-common.h:39:3: note: in expansion of macro '_FP_FRAC_DECL_2'
39 | _FP_FRAC_DECL_##wc (X)
| ^~~~~~~~~~~~~~
../soft-fp/quad.h:226:24: note: in expansion of macro '_FP_DECL'
226 | # define FP_DECL_Q(X) _FP_DECL (2, X)
| ^~~~~~~~
../sysdeps/ieee754/soft-fp/s_fdivl.c:37:3: note: in expansion of macro 'FP_DECL_Q'
37 | FP_DECL_Q (R);
| ^~~~~~~~~
../soft-fp/op-2.h:109:8: error: 'R_f0' may be used uninitialized in this function [-Werror=maybe-uninitialized]
109 | | X##_f0) != 0)); \
| ^
../sysdeps/ieee754/soft-fp/s_fdivl.c:37:14: note: 'R_f0' was declared here
37 | FP_DECL_Q (R);
| ^
../soft-fp/op-common.h:39:3: note: in expansion of macro '_FP_FRAC_DECL_2'
39 | _FP_FRAC_DECL_##wc (X)
| ^~~~~~~~~~~~~~
../soft-fp/quad.h:226:24: note: in expansion of macro '_FP_DECL'
226 | # define FP_DECL_Q(X) _FP_DECL (2, X)
| ^~~~~~~~
../sysdeps/ieee754/soft-fp/s_fdivl.c:37:3: note: in expansion of macro 'FP_DECL_Q'
37 | FP_DECL_Q (R);
| ^~~~~~~~~
In file included from ../soft-fp/soft-fp.h:318,
from ../sysdeps/ieee754/soft-fp/s_ddivl.c:31:
../sysdeps/ieee754/soft-fp/s_ddivl.c: In function '__ddivl':
../soft-fp/op-2.h:98:25: error: 'R_f1' may be used uninitialized in this function [-Werror=maybe-uninitialized]
98 | X##_f0 = (X##_f1 << (_FP_W_TYPE_SIZE - (N)) | X##_f0 >> (N) \
| ^~
../sysdeps/ieee754/soft-fp/s_ddivl.c:41:14: note: 'R_f1' was declared here
41 | FP_DECL_Q (R);
| ^
../soft-fp/op-2.h:37:36: note: in definition of macro '_FP_FRAC_DECL_2'
37 | _FP_W_TYPE X##_f0 _FP_ZERO_INIT, X##_f1 _FP_ZERO_INIT
| ^
../soft-fp/quad.h:226:24: note: in expansion of macro '_FP_DECL'
226 | # define FP_DECL_Q(X) _FP_DECL (2, X)
| ^~~~~~~~
../sysdeps/ieee754/soft-fp/s_ddivl.c:41:3: note: in expansion of macro 'FP_DECL_Q'
41 | FP_DECL_Q (R);
| ^~~~~~~~~
../soft-fp/op-2.h:101:17: error: 'R_f0' may be used uninitialized in this function [-Werror=maybe-uninitialized]
101 | : (X##_f0 << (_FP_W_TYPE_SIZE - (N))) != 0)); \
| ^~
../sysdeps/ieee754/soft-fp/s_ddivl.c:41:14: note: 'R_f0' was declared here
41 | FP_DECL_Q (R);
| ^
../soft-fp/op-2.h:37:14: note: in definition of macro '_FP_FRAC_DECL_2'
37 | _FP_W_TYPE X##_f0 _FP_ZERO_INIT, X##_f1 _FP_ZERO_INIT
| ^
../soft-fp/quad.h:226:24: note: in expansion of macro '_FP_DECL'
226 | # define FP_DECL_Q(X) _FP_DECL (2, X)
| ^~~~~~~~
../sysdeps/ieee754/soft-fp/s_ddivl.c:41:3: note: in expansion of macro 'FP_DECL_Q'
41 | FP_DECL_Q (R);
| ^~~~~~~~~
cc1: all warnings being treated as errors
make[2]: *** [.../sysd-rules:587: .../math/s_fdivl.o] Error 1
make[2]: *** Waiting for unfinished jobs....
cc1: all warnings being treated as errors
make[2]: *** [.../sysd-rules:587: .../math/s_ddivl.o] Error 1
This comes from cases in _FP_DIV that return a result described as
FP_CLS_ZERO or FP_CLS_INF and do not initialize the fractional part,
which is then operated on unconditionally in FP_TRUNC_COOKED before
being ignored by _FP_PACK_CANONICAL.
Clearly at this optimization level GCC cannot guarantee to be able to
determine that the fractional part is ultimately unused, so ignore the
error as with the earlier commits referred, letting compilation proceed.
[BZ #19444]
* sysdeps/ieee754/soft-fp/s_ddivl.c (__ddivl): Ignore errors
from `-Wmaybe-uninitialized'.
* sysdeps/ieee754/soft-fp/s_fdivl.c (__fdivl): Likewise.
This patch adds test cases for the compatibility versions of the
functions: err, errx, verr, verrx, warn, warnx, vwarn, vwarnx (from
err.h), error, and error_at_line (from error.h), when long double has
the same format as double (-mlong-double-64).
Tested for powerpc, powerpc64 and powerpc64le.
On platforms where long double may have the same format as double
(-mlong-double-64), error and error_at_line do not take that into
account and might produce wrong output if a long double conversion is
requested by the format string ('%Lf'). This patch adds compatibility
functions for this situation and redirects calls via header magic.
Tested for powerpc, powerpc64 and powerpc64le.
When support for long double format with 128-bits (-mlong-double-128)
was added for platforms where long double had the same format as double,
such as powerpc, compatibility versions for the functions listed in the
commit title were missed. Since the older format of long double can
still be used (with -mlong-double-64), using these functions with a
format string that requests the printing of long double variables will
produce wrong outputs.
This patch adds the missing compatibility functions and header magic to
redirect calls to them when -mlong-double-64 is in use.
Tested for powerpc, powerpc64 and powerpc64le.
The test case tst-ldbl-argp checks that the conversion specifier '%Lf'
correctly prints long double values with the default long double format
for a platform. This patch reuses the test case for long double with
the same format as double (-mlong-double-64).
Tested for powerpc, powerpc64 and powerpc64le.
The functions argp_error and argp_failure are missing support for
printing long double values when long double has the same format as
double. This patch adds the new functions __nldbl_argp_error and
__nldbl_argp_failure, as well as header magic to redirect calls to them
when -mlong-double-64 is in use.
Tested for powerpc, powerpc64 and powerpc64le.
One group of warnings seen with -Wextra is warnings for static or
inline not at the start of a declaration (-Wold-style-declaration).
This patch fixes various such cases for inline, ensuring it comes at
the start of the declaration (after any static). A common case of the
fix is "static inline <type> __always_inline"; the definition of
__always_inline starts with __inline, so the natural change is to
"static __always_inline <type>". Other cases of the warning may be
harder to fix (one pattern is a function definition that gets
rewritten to be static by an including file, "#define funcname static
wrapped_funcname" or similar), but it seems worth fixing these cases
with inline anyway.
Tested for x86_64.
* elf/dl-load.h (_dl_postprocess_loadcmd): Use __always_inline
before return type, without separate inline.
* elf/dl-tunables.c (maybe_enable_malloc_check): Likewise.
* elf/dl-tunables.h (tunable_is_name): Likewise.
* malloc/malloc.c (do_set_trim_threshold): Likewise.
(do_set_top_pad): Likewise.
(do_set_mmap_threshold): Likewise.
(do_set_mmaps_max): Likewise.
(do_set_mallopt_check): Likewise.
(do_set_perturb_byte): Likewise.
(do_set_arena_test): Likewise.
(do_set_arena_max): Likewise.
(do_set_tcache_max): Likewise.
(do_set_tcache_count): Likewise.
(do_set_tcache_unsorted_limit): Likewise.
* nis/nis_subr.c (count_dots): Likewise.
* nptl/allocatestack.c (advise_stack_range): Likewise.
* sysdeps/ieee754/dbl-64/s_sin.c (do_cos): Likewise.
(do_sin): Likewise.
(reduce_sincos): Likewise.
(do_sincos): Likewise.
* sysdeps/unix/sysv/linux/x86/elision-conf.c
(do_set_elision_enable): Likewise.
(TUNABLE_CALLBACK_FNDECL): Likewise.
With -O included in CFLAGS it fails to build with:
../sysdeps/ieee754/ldbl-96/e_jnl.c: In function '__ieee754_jnl':
../sysdeps/ieee754/ldbl-96/e_jnl.c:146:20: error: 'temp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
b = invsqrtpi * temp / sqrtl (x);
~~~~~~~~~~^~~~~~
../sysdeps/ieee754/ldbl-96/e_jnl.c: In function '__ieee754_ynl':
../sysdeps/ieee754/ldbl-96/e_jnl.c:375:16: error: 'temp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
b = invsqrtpi * temp / sqrtl (x);
~~~~~~~~~~^~~~~~
../sysdeps/ieee754/dbl-64/e_jn.c: In function '__ieee754_jn':
../sysdeps/ieee754/dbl-64/e_jn.c:113:20: error: 'temp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
b = invsqrtpi * temp / sqrt (x);
~~~~~~~~~~^~~~~~
../sysdeps/ieee754/dbl-64/e_jn.c: In function '__ieee754_yn':
../sysdeps/ieee754/dbl-64/e_jn.c:320:16: error: 'temp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
b = invsqrtpi * temp / sqrt (x);
~~~~~~~~~~^~~~~~
Build tested with Yocto for ARM, AARCH64, X86, X86_64, PPC, MIPS, MIPS64
with -O, -O1, -Os.
For AARCH64 it needs one more fix in locale for -Os:
https://sourceware.org/ml/libc-alpha/2018-09/msg00539.html
[BZ #19444]
* sysdeps/ieee754/dbl-64/e_jn.c (__ieee754_jn): Use
__builtin_unreachable for default case in switch.
(__ieee754_yn): Likewise.
* sysdeps/ieee754/ldbl-96/e_jnl.c (__ieee754_jnl): Likewise.
(__ieee754_ynl): Likewise.
* sysdeps/ieee754/ldbl-128/e_jnl.c (__ieee754_jnl): Likewise.
(__ieee754_ynl): Likewise.
* sysdeps/ieee754/ldbl-128ibm/e_jnl.c (__ieee754_jnl): Likewise.
(__ieee754_ynl): Likewise.
The only difference between noncompliant and C99-compliant scanf is
that the former accepts the archaic GNU extension '%as' (also %aS and
%a[...]) meaning to allocate space for the input string with malloc.
This extension conflicts with C99's use of %a as a format _type_
meaning to read a floating-point number; POSIX.1-2008 standardized
equivalent functionality using the modifier letter 'm' instead (%ms,
%mS, %m[...]).
The extension was already disabled in most conformance modes:
specifically, any mode that doesn't involve _GNU_SOURCE and _does_
involve either strict conformance to C99 or loose conformance to both
C99 and POSIX.1-2001 would get the C99-compliant scanf. With
compilers new enough to use -std=gnu11 instead of -std=gnu89, or
equivalent, that includes the default mode.
With this patch, we now provide C99-compliant scanf in all
configurations except when _GNU_SOURCE is defined *and*
__STDC_VERSION__ or __cplusplus (whichever is relevant) indicates
C89/C++98. This leaves the old scanf available under e.g. -std=c89
-D_GNU_SOURCE, but removes it from e.g. -std=gnu11 -D_GNU_SOURCE (it
was already not present under -std=gnu11 without -D_GNU_SOURCE) and
from -std=gnu89 without -D_GNU_SOURCE.
There needs to be an internal override so we can compile the
noncompliant scanf itself. This is the same problem we had when we
removed 'gets' from _GNU_SOURCE and it's dealt with the same way:
there's a new __GLIBC_USE symbol, DEPRECATED_SCANF, which defaults to
off under the appropriate conditions for external code, but can be
overridden by individual files within stdio.
We also run into problems with PLT bypass for internal uses of sscanf,
because libc_hidden_proto uses __REDIRECT and so does the logic in
stdio.h for choosing which implementation of scanf to use; __REDIRECT
isn't transitive, so include/stdio.h needs to bridge the gap with a
macro. As far as I can tell, sscanf is the only function in this
family that's internally called by unrelated code.
Finally, there are several tests in stdio-common that use the
extension. bug21.c is a regression test for a crash; it still
exercises the relevant code when changed to use %ms instead of %as.
scanf14.c through scanf17.c are more complicated since they are
actually testing the subtleties of the extension - under what
circumstances is 'a' treated as a modifier letter, etc. I changed all
of them to use %ms instead of %as as well, but duplicated scanf14.c
and scanf16.c as scanf14a.c and scanf16a.c. These still use %as and
are compiled with -std=gnu89 to access the old extension. A bunch of
diagnostic overrides and manual workarounds for the old stdio.h
behavior become unnecessary. Yay!
* include/features.h (__GLIBC_USE_DEPRECATED_SCANF): New __GLIBC_USE
parameter. Only use deprecated scanf when __USE_GNU is defined
and __STDC_VERSION__ is less than 199901L or __cplusplus is less
than 201103L, whichever is relevant for the language being compiled.
* libio/stdio.h, libio/bits/stdio-ldbl.h: Decide whether to redirect
scanf, fscanf, sscanf, vscanf, vfscanf, and vsscanf to their
__isoc99_ variants based only on __GLIBC_USE (DEPRECATED_SCANF).
* wcsmbs/wchar.h: wcsmbs/bits/wchar-ldbl.h: Likewise for
wscanf, fwscanf, swscanf, vwscanf, vfwscanf, and vswscanf.
* libio/iovsscanf.c
* libio/fwscanf.c
* libio/iovswscanf.c
* libio/swscanf.c
* libio/vscanf.c
* libio/vwscanf.c
* libio/wscanf.c
* stdio-common/fscanf.c
* stdio-common/scanf.c
* stdio-common/vfscanf.c
* stdio-common/vfwscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-compat.c
* sysdeps/ieee754/ldbl-opt/nldbl-fscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-fwscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-iovfscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-scanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-sscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-swscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vfscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vfwscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vsscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vswscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-vwscanf.c
* sysdeps/ieee754/ldbl-opt/nldbl-wscanf.c:
Override __GLIBC_USE_DEPRECATED_SCANF to 1.
* stdio-common/sscanf.c: Likewise. Remove ldbl_hidden_def for __sscanf.
* stdio-common/isoc99_sscanf.c: Add libc_hidden_def for __isoc99_sscanf.
* include/stdio.h: Provide libc_hidden_proto for __isoc99_sscanf,
not sscanf.
[!__GLIBC_USE (DEPRECATED_SCANF)]: Define sscanf as __isoc99_scanf
with a preprocessor macro.
* stdio-common/bug21.c, stdio-common/scanf14.c:
Use %ms instead of %as, %mS instead of %aS, %m[] instead of %a[];
remove DIAG_IGNORE_NEEDS_COMMENT for -Wformat.
* stdio-common/scanf16.c: Likewise. Add __attribute__ ((format (scanf)))
to xscanf, xfscanf, xsscanf.
* stdio-common/scanf14a.c: New copy of scanf14.c which still uses
%as, %aS, %a[]. Remove DIAG_IGNORE_NEEDS_COMMENT for -Wformat.
* stdio-common/scanf16a.c: New copy of scanf16.c which still uses
%as, %aS, %a[]. Add __attribute__ ((format (scanf))) to xscanf,
xfscanf, xsscanf.
* stdio-common/scanf15.c, stdio-common/scanf17.c: No need to
override feature selection macros or provide definitions of u_char etc.
* stdio-common/Makefile (tests): Add scanf14a and scanf16a.
(CFLAGS-scanf15.c, CFLAGS-scanf17.c): Remove.
(CFLAGS-scanf14a.c, CFLAGS-scanf16a.c): New. Compile these files
with -std=gnu89.
