They are not needed, because anything that is non-zero is converted
to true.
C11:
> 6.3.1.2: When any scalar value is converted to _Bool, the result is 0 if the
> value compares equal to 0; otherwise, the result is 1.
https://stackoverflow.com/questions/31551888/casting-int-to-bool-in-c-c
Files which are installed as-is (any .service and other unit files, .conf
files, .policy files, etc), are left as is. My assumption is that SPDX
identifiers are not yet that well known, so it's better to retain the
extended header to avoid any doubt.
I also kept any copyright lines. We can probably remove them, but it'd nice to
obtain explicit acks from all involved authors before doing that.
Once upon a time shutdown.c didn't have the logic to check whether any
unmount attempts succeeded or not. So instead it kept looping for
a fixed amount and hoped all was right. Nowadays, we do know if we
changed anything during a iteration and also stop looping then, but
we still limit ourselves to FINALIZE_ATTEMPTS.
But, theoretically, we could have such a complicated and nested
setup that would survive that limit, leaving stuff around we
might actually be able to unmount. And we could also end up in a
situation where the extra loop with raised unmount error level could
be skipped too.
So let's just drop the retries logic and rely fully on the changed
flag.
There is little point in logging about unmounting errors if the
exact mountpoint will be successfully unmounted in a later retry
due unmounts below it having been removed.
Additionally, don't log those errors if we are going to switch back
to a initrd, because that one is also likely to finalize the remaining
mountpoints. If not, it will log errors then.
Generally we prefer 'return' from main() over exit() so that automatic
cleanups and such work correct. Let's do that in shutdown.c too, becuase
there's not really any reason not to.
With this we are pretty good in consistently using return from main()
rather than exit() all across the codebase. Yay!
So far, we had two implementations of reboot-with-parameter doing pretty
much the same. Let's unify that in a generic implementation used by
both.
This is particulary nice as it unifies all /run/systemd/reboot-param
handling in a single .c file.
This mimics the raw_clone() call we have in place already and
establishes a new syscall wrapper raw_reboot() that wraps the kernel's
reboot() system call in a bit more low-level fashion that glibc's
reboot() wrapper. The main difference is that the extra "arg" argument
is supported.
Ultimately this just replaces the syscall wrapper implementation we
currently have at three places in our codebase by a single one.
With this change this means that all our syscall() invocations are
neatly separated out in static inline system call wrappers in our header
functions.
We used to set this, but this was dropped when shutdown got taught to
get the target passed in from the regular PID 1. Let's readd this to
make things more explanatory, and cover all grounds, since after all the
target passed is in theory an optional part of the protocol between the
regular PID 1 and the shutdown PID 1.
Now we have log_set_prohibit_ipc(), let's use it to clarify that
systemd-shutdown is not expected to try and log via journald (which it is
about to kill). We avoided ever asking systemd-shutdown to do this, but
it's more convenient for the reader if they don't have to think about that.
In that sense, it's similar to using assert() to validate a function's
arguments.
log_open_console() did not switch from stderr to /dev/console, when
"always_reopen_console" was set. It was necessary to call
log_close_console() first.
By contrast, log_open() did switch between e.g. journald and kmsg according
to the value of "prohibit_ipc".
Let's fix log_open() to respect the values of all the log options, and we
can make log_close_*() private.
Also log_close_console() is changed. There was some precaution, avoiding
closing the console fd if we are not PID 1. I think commit 48a601fe made
a little mistake in leaving this in, and it only served to confuse
readers :).
Also I changed systemd-shutdown. Now we have log_set_prohibit_ipc(), let's
use it to clarify that systemd-shutdown is not expected to try and log via
journald (which it is about to kill). We avoided ever asking it to, but
it's more convenient for the reader if they don't have to think about that.
In that sense, it's similar to using assert() to validate a function's
arguments.
By default systemd-shutdown will wait for 90s after SIGTERM was sent
for all processes to exit. This is way too long and effectively defeats
an emergency watchdog reboot via "reboot-force" actions. Instead now
use DefaultTimeoutStopSec which is configurable.
First, let's rename it to disable_coredumps(), as in the rest of our
codebase we spell it "coredump" rather than "core_dump", so let's stick
to that.
However, also log about failures to turn off core dumpling on LOG_DEBUG,
because debug logging is always a good idea.
If the system is finally shutting down it makes no sense to write core
dumps as the last remaining processes are terminated / killed. This is
especially significant in case of a "force reboot" where all processes
are hit concurrently with a SIGTERM and no orderly shutdown of
processes takes place.
This new flag will cause safe_fork() to wait for the forked off child
before returning. This allows us to unify a number of cases where we
immediately wait on the forked off child, witout running any code in the
parent after the fork, and without direct interest in the precise exit
status of the process, except recgonizing EXIT_SUCCESS vs everything
else.
This renames wait_for_terminate_and_warn() to
wait_for_terminate_and_check(), and adds a flags parameter, that
controls how much to log: there's one flag that means we log about
abnormal stuff, and another one that controls whether we log about
non-zero exit codes. Finally, there's a shortcut flag value for logging
in both cases, as that's what we usually use.
All callers are accordingly updated. At three occasions duplicate logging
is removed, i.e. where the old function was called but logged in the
caller, too.
This adds a new safe_fork() wrapper around fork() and makes use of it
everywhere. The new wrapper does a couple of things we previously did
manually and separately in a safer, more correct and automatic way:
1. Optionally resets signal handlers/mask in the child
2. Sets a name on all processes we fork off right after forking off (and
the patch assigns useful names for all processes we fork off now,
following a systematic naming scheme: always enclosed in () – in order
to indicate that these are not proper, exec()ed processes, but only
forked off children, and if the process is long-running with only our
own code, without execve()'ing something else, it gets am "sd-" prefix.)
3. Optionally closes all file descriptors in the child
4. Optionally sets a PR_SET_DEATHSIG to SIGTERM in the child, in a safe
way so that the parent dying before this happens being handled
safely.
5. Optionally reopens the logs
6. Optionally connects stdin/stdout/stderr to /dev/null
7. Debug logs about the forked off processes.
In similar fashion to the previous change, sync() operations can stall
endlessly if cache is unable to be written out. In order to avoid an
unbounded hang, the sync takes place within a child process. Every 10
seconds (SYNC_TIMEOUT_USEC), the value of /proc/meminfo "Dirty" is checked
to verify it is smaller than the last iteration. If the sync is not making
progress for 3 successive iterations (SYNC_PROGRESS_ATTEMPTS), a SIGKILL is
sent to the sync process and the shutdown continues.
This option allows a device path to be specified for the systemd
watchdog (both runtime and shutdown).
If a system requires a watchdog other than /dev/watchdog (pointing to
/dev/watchdog0) to be used to reboot the system, this setting should be
changed to the relevant watchdog device path (e.g. /dev/watchdog1).
This moves pretty much all uses of getpid() over to getpid_raw(). I
didn't specifically check whether the optimization is worth it for each
replacement, but in order to keep things simple and systematic I
switched over everything at once.
$ reboot -f
Failed to read reboot parameter file: No such file or directory
It seems that the warning on ENOENT was inadvertently introduced in
27c06cb516.
The warning reported in #5646 comes from systemctl, but let's fix the other
call site in the same way too.
Fixes#5646.
The output of processes can be gathered, and passed back to the callee.
(This commit just implements the basic functionality and tests.)
After the preparation in previous commits, the change in functionality is
relatively simple. For coding convenience, alarm is prepared *before* any
children are executed, and not before. This shouldn't matter usually, since
just forking of the children should be pretty quick. One could also argue that
this is more correct, because we will also catch the case when (for whatever
reason), forking itself is slow.
Three callback functions and three levels of serialization are used:
- from individual generator processes to the generator forker
- from the forker back to the main process
- deserialization in the main process
v2:
- replace an structure with an indexed array of callbacks
Always warn if something fails, and clarify that the involved utility functions
do so in their name.
Drop the REBOOT_PARAM_FILE macro. We don't do this for other flag file paths
like this, so don't do this for this one either. The path isn't configurable
anyway, hence let's make this easier to read by avoiding this one indirection.
There are more than enough calls doing string manipulations to deserve
its own files, hence do something about it.
This patch also sorts the #include blocks of all files that needed to be
updated, according to the sorting suggestions from CODING_STYLE. Since
pretty much every file needs our string manipulation functions this
effectively means that most files have sorted #include blocks now.
Also touches a few unrelated include files.
This introduces a new systemd.crash_reboot=1 kernel command line option
that triggers a reboot after crashing.
This also cleans up crash VT handling. Specifically, it cleans up the
configuration setting, to be between 1..63 or a boolean. This is to
replace the previous logic where "-1" meant disabled. We continue to
accept that setting, but only document the boolean syntax instead.
This also brings the documentation of the default settings in sync with
what actually happens.
The CrashChVT= configuration file setting is renamed to CrashChangeVT=,
following our usual logic of not abbreviating unnecessarily. The old
setting stays support for compat reasons.
Fixes#1300
When a systemd service running in a container exits with a non-zero
code, it can be useful to terminate the container immediately and get
the exit code back to the host, when systemd-nspawn returns. This was
not possible to do. This patch adds the following to make it possible:
- Add a read-only "ExitCode" property on PID 1's "Manager" bus object.
By default, it is 0 so the behaviour stays the same as previously.
- Add a method "SetExitCode" on the same object. The method fails when
called on baremetal: it is only allowed in containers or in user
session.
- Add support in systemctl to call "systemctl exit 42". It reuses the
existing code for user session.
- Add exit.target and systemd-exit.service to the system instance.
- Change main() to actually call systemd-shutdown to exit() with the
correct value.
- Add verb 'exit' in systemd-shutdown with parameter --exit-code
- Update systemctl manpage.
I used the following to test it:
| $ sudo rkt --debug --insecure-skip-verify run \
| --mds-register=false --local docker://busybox \
| --exec=/bin/chroot -- /proc/1/root \
| systemctl --force exit 42
| ...
| Container rkt-895a0cba-5c66-4fa5-831c-e3f8ddc5810d failed with error code 42.
| $ echo $?
| 42
Fixes https://github.com/systemd/systemd/issues/1290
Turns this:
r = -errno;
log_error_errno(errno, "foo");
into this:
r = log_error_errno(errno, "foo");
and this:
r = log_error_errno(errno, "foo");
return r;
into this:
return log_error_errno(errno, "foo");
Introduce a proper enum, and don't pass around string ids anymore. This
simplifies things quite a bit, and makes virtualization detection more
similar to architecture detection.
This patch removes includes that are not used. The removals were found with
include-what-you-use which checks if any of the symbols from a header is
in use.
Sometimes it is necessary to stop a generator from running. Either
because of a bug, or for testing, or some other reason. The only way
to do that would be to rename or chmod the generator binary, which is
inconvenient and does not survive upgrades. Allow masking and
overriding generators similarly to units and other configuration
files.
For the systemd instance, masking would be more common, rather than
overriding generators. For the user instances, it may also be useful
for users to have generators in $XDG_CONFIG_HOME to augment or
override system-wide generators.
Directories are searched according to the usual scheme (/usr/lib,
/usr/local/lib, /run, /etc), and files with the same name in higher
priority directories override files with the same name in lower
priority directories. Empty files and links to /dev/null mask a given
name.
https://bugs.freedesktop.org/show_bug.cgi?id=87230
Remove the optional sepearate opening of the directory,
it would be just too complicated with the change to
multiple directories.
Move the middle of execute_directory() to a seperate
function to make it easier to grok.
If the format string contains %m, clearly errno must have a meaningful
value, so we might as well use log_*_errno to have ERRNO= logged.
Using:
find . -name '*.[ch]' | xargs sed -r -i -e \
's/log_(debug|info|notice|warning|error|emergency)\((".*%m.*")/log_\1_errno(errno, \2/'
Plus some whitespace, linewrap, and indent adjustments.
